Firmware Version 6.1 Duplex Console IO Dependent Code (IODC) revision 1 Memory Test/Initialization Completed ------------------------------------------------------------------------------ (c) Copyright 1995-1998, Hewlett-Packard Company, All rights reserved ------------------------------------------------------------------------------ Processor Speed State Coprocessor State Cache Size --------- -------- --------------------- ----------------- ---------- 0 160 MHz Active Functional 64 KB 1 MB ext Available memory (bytes) : 134217728 Good memory required (bytes): 134217728 Primary boot path: FWSCSI.6.0 Alternate boot path: LAN.0.0.0.0.0.0 Console path: SERIAL_1.9600.8.none Keyboard path: PS2 CPU 0 WARNING: Self tests have been disabled as a result of FASTBOOT being enabled. To enable self tests, use the FASTBOOT command in the CONFIGURATION menu and reboot the system. ------- Main Menu ------------------------------------------------------------- Command Description ------- ----------- BOot [PRI|ALT|] Boot from specified path PAth [PRI|ALT|CON|KEY] [] Display or modify a path SEArch [DIsplay|IPL] [] Search for boot devices COnfiguration [] Access Configuration menu/commands INformation [] Access Information menu/commands SERvice [] Access Service menu/commands DIsplay Redisplay the current menu HElp [|] Display help for menu or command RESET Restart the system ------- Main Menu: Enter command > bo pri Interact with IPL (Y, N, Q)?> n Booting... Boot IO Dependent Code (IODC) revision 153 HARD Booted. palo ipl 2.14 https://parisc.wiki.kernel.org - Sat, 30 May 2020 22:20:30 +0000 Partition Start(MB) End(MB) Id Type 1 1 31 f0 Palo 2 32 156 83 ext2 5 157 1906 83 ext2 6 1907 2047 82 swap PALO(F0) partition contains: 0/vmlinux32 3615504(0) bytes @ 0x48000 0/ramdisk 22508811 bytes @ 0x3bab10 Information: No console specified on kernel command line. This is normal. PALO will choose the console currently used by firmware (serial). Command line for kernel: 'root=/dev/sda5 HOME=/ cryptomgr.notests console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux' Selected kernel: /vmlinux from partition 2 Selected ramdisk: /initrd.img from partition 2 ELF32 executable Segment 0 load 000e0000 size 3665660 mediaptr 0x1000 Segment 1 load 00cc3000 size 18804 mediaptr 0x380000 Loading ramdisk 23717872 bytes @ 06950000... Branching to kernel entry point 0x000e0000. If this is the last message you see, you may need to switch your console. This is a common symptom -- search the FAQ and mailing list at https://parisc.wiki.kernel.org Decompressing Linux... done. Booting the kernel. [ 0.000000] Linux version 5.8.0-2-parisc (debian-kernel@lists.debian.org) (gcc-10 (Debian 10.2.0-8) 10.2.0, GNU ld (GNU Binutils for Debian) 2.35) #1 SMP Debian 5.8.10-1 (2020-09-19) [ 0.000000] CPU0: thread -1, cpu 0, socket 0 [ 0.000000] FP[0] enabled: Rev 1 Model 15 [ 0.000000] The 32-bit Kernel has started... [ 0.000000] Kernel default page size is 4 KB. Huge pages disabled. [ 0.000000] printk: bootconsole [ttyB0] enabled [ 0.000000] Initialized PDC Console for debugging. [ 0.000000] Determining PDC firmware type: System Map. [ 0.000000] model 00005020 00000481 00000000 02020202 7794d7fe 100000f0 00000004 000000ba 000000ba [ 0.000000] vers 00000008 [ 0.000000] CPUID vers 15 rev 8 (0x000001e8) [ 0.000000] capabilities 0x2 [ 0.000000] model 9000/778/B160L [ 0.000000] Memory Ranges: [ 0.000000] 0) Start 0x0000000000000000 End 0x0000000007ffffff Size 128 MB [ 0.000000] Total Memory: 128 MB [ 0.000000] initrd: 16950000-17fee7f0 [ 0.000000] initrd: reserving 06950000-07fee7f0 (mem_max 08000000) [ 0.000000] PDT: Firmware does not provide any page deallocation information. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000007fffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] LED display at f0190001 registered [ 0.000000] percpu: Embedded 27 pages/cpu s81616 r8192 d20784 u110592 [ 0.000000] SMP: bootstrap CPU ID is 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: root=/dev/sda5 HOME=/ cryptomgr.notests console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 94012K/131072K available (8380K kernel code, 1006K rwdata, 1432K rodata, 652K init, 572K bss, 37060K reserved, 0K cma-reserved) [ 0.000000] random: get_random_u32 called from __kmem_cache_create+0x58/0x5f4 with crng_init=0 [ 0.000000] SLUB: HWalign=16, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 22540 entries in 45 pages [ 0.000000] ftrace: allocated 45 pages with 4 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 96 [ 0.000052] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 13421772796ns [ 0.100898] Console: colour dummy device 160x64 [ 0.158054] Calibrating delay loop... 105.47 BogoMIPS (lpj=210944) [ 0.274043] pid_max: default: 32768 minimum: 301 [ 0.335737] LSM: Security Framework initializing [ 0.394320] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.479898] AppArmor: AppArmor initialized [ 0.530093] TOMOYO Linux initialized [ 0.574676] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.666123] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.784418] rcu: Hierarchical SRCU implementation. [ 0.852950] smp: Bringing up secondary CPUs ... [ 0.906177] smp: Brought up 1 node, 1 CPU [ 0.964882] devtmpfs: initialized [ 1.016120] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 1.138633] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 1.228225] thermal_sys: Registered thermal governor 'fair_share' [ 1.228259] thermal_sys: Registered thermal governor 'step_wise' [ 1.310368] NET: Registered protocol family 16 [ 1.443050] audit: initializing netlink subsys (disabled) [ 1.516241] EISA bus registered [ 1.554373] audit: type=2000 audit(1604234474.508:1): state=initialized audit_enabled=0 res=1 [ 1.662203] Searching for devices... [ 2.612829] Found devices: [ 2.646114] 1. Phantom PseudoBC GSC+ Port at 0xffc00000 [8] { 7, 0x0, 0x504, 0x00000 } [ 2.746095] 2. Dino PCI Bridge at 0xfff80000 [8/0] { 13, 0x3, 0x680, 0x0000a } [ 2.834117] 3. Merlin+ 132 Dino RS-232 at 0xfff83000 [8/0/63] { 10, 0x0, 0x022, 0x0008c } [ 2.938095] 4. Merlin 160 Core FW-SCSI at 0xfff8c000 [8/12] { 4, 0x0, 0x03d, 0x00089 } [ 3.038094] 5. Merlin 160 Core BA at 0xffd00000 [8/16] { 11, 0x0, 0x03d, 0x00081 }, additional addresses: 0xffd0c000 0xffc00000 [ 3.182095] 6. Merlin 160 Core RS-232 at 0xffd05000 [8/16/4] { 10, 0x0, 0x03d, 0x0008c } [ 3.286096] 7. Merlin 160 Core SCSI at 0xffd06000 [8/16/5] { 10, 0x0, 0x03d, 0x00082 } [ 3.386097] 8. Merlin 160 Core LAN (802.3) at 0xffd07000 [8/16/6] { 10, 0x0, 0x03d, 0x0008a } [ 3.490098] 9. Merlin 160 Core Centronics at 0xffd02000 [8/16/0] { 10, 0x0, 0x03d, 0x00074 }, additional addresses: 0xffd01000 0xffd03000 [ 3.650099] 10. Merlin 160 Core Audio at 0xffd04000 [8/16/1] { 10, 0x4, 0x03d, 0x0007b } [ 3.750097] 11. Merlin 160 Core PS/2 Port at 0xffd08000 [8/16/7] { 10, 0x0, 0x03d, 0x00084 } [ 3.858096] 12. Merlin 160 Core PS/2 Port at 0xffd08100 [8/16/8] { 10, 0x0, 0x03d, 0x00084 } [ 3.962094] 13. Coral SGC Graphics at 0xfa000000 [8/4] { 10, 0x0, 0x004, 0x00077 } [ 4.058094] 14. Coral SGC Graphics at 0xf4000000 [8/8] { 10, 0x0, 0x004, 0x00077 } [ 4.154094] 15. Gecko GSC Core Graphics at 0xf8000000 [8/24] { 10, 0x0, 0x016, 0x00085 }, additional addresses: 0xf0011000 [ 4.294093] 16. Merlin L2 160 (9000/778/B160L) at 0xfffbe000 [62] { 0, 0x0, 0x502, 0x00004 } [ 4.398087] 17. Memory at 0xfffbf000 [63] { 1, 0x0, 0x067, 0x00009 } [ 4.478089] 18. Merlin+ 132 Dino PS/2 Port at 0xfff81000 [1] { 10, 0x0, 0x022, 0x00096 } [ 4.582077] Enabling regular chassis codes support v0.05 [ 4.782927] CPU(s): 1 out of 1 PA7300LC (PCX-L2) at 160.000000 MHz online [ 4.866722] alternatives: applied 216 out of 254 patches [ 4.945288] Cache flush threshold set to 2 KiB [ 5.002400] Whole TLB flush 2140 cycles, Range flush 11665408 bytes 186863 cycles [ 5.094066] Calculated TLB flush threshold 20 KiB [ 5.154055] TLB flush threshold set to 20 KiB [ 5.211323] Lasi version 0 at 0xffd00000 found. [ 5.270926] Dino version 3.1 found at 0xfff80000 [ 5.326372] Dino: No PCI devices enabled. [ 5.378781] dino 8:0: PCI host bridge to bus 0000:00 [ 5.442132] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 5.518112] pci_bus 0000:00: root bus resource [bus 00-ff] [ 5.590134] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 5.674370] powersw: Soft power switch at 0xf0140000 enabled. [ 5.823523] vgaarb: loaded [ 5.869682] NetLabel: Initializing [ 5.910092] NetLabel: domain hash size = 128 [ 5.966062] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 6.039086] NetLabel: unlabeled traffic allowed by default [ 6.418074] random: fast init done [ 6.714489] VFS: Disk quotas dquot_6.6.0 [ 6.762790] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 6.858479] AppArmor: AppArmor Filesystem Enabled [ 6.985711] NET: Registered protocol family 2 [ 7.048194] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 6144 bytes, linear) [ 7.154405] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 7.250743] TCP bind hash table entries: 1024 (order: 2, 20480 bytes, linear) [ 7.338344] TCP: Hash tables configured (established 1024 bind 1024) [ 7.423224] UDP hash table entries: 256 (order: 1, 12288 bytes, linear) [ 7.506463] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes, linear) [ 7.595821] NET: Registered protocol family 1 [ 7.650234] NET: Registered protocol family 44 [ 7.706117] PCI: CLS 16 bytes [ 7.748465] Trying to unpack rootfs image as initramfs... [ 19.408143] Freeing initrd memory: 23160K [ 19.458357] clocksource: cr16: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11945377789 ns [ 19.570448] clocksource: Switched to clocksource cr16 [ 19.634475] Enabling PDC chassis warnings support v0.05 [ 19.706358] Initialise system trusted keyrings [ 19.762546] Key type blacklist registered [ 19.815552] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 19.946728] zbud: loaded [ 19.986787] integrity: Platform Keyring initialized [ 20.048454] Key type asymmetric registered [ 20.100289] Asymmetric key parser 'x509' registered [ 20.161984] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 20.256358] io scheduler mq-deadline registered [ 20.320879] PDC Stable Storage facility v0.30 [ 20.457539] STI GSC/PCI core graphics driver Version 0.9b [ 20.548743] STI ROM supports 32 bit firmware functions. [ 20.614594] STI selected 8x16 framebuffer font VGA8x16 for sticon [ 20.692165] id 2bcb015a-9a02587, conforms to spec rev. 8.04 [ 21.082751] graphics card name: HPA4071B [ 21.214449] STI ROM supports 32 bit firmware functions. [ 21.280259] STI selected 8x16 framebuffer font VGA8x16 for sticon [ 21.357796] id 2d08c0a7-9a02587, conforms to spec rev. 8.07 [ 21.434467] graphics card name: HPA4450AX1024 [ 21.508360] STI ROM supports 32 bit firmware functions. [ 21.574175] STI selected 8x16 framebuffer font VGA8x16 for sticon [ 21.651238] id 2d08c0a7-9a02587, conforms to spec rev. 8.07 [ 21.728291] graphics card name: INTERNAL_EG_X800 [ 21.791695] sticon: Initializing STI text console. [ 21.860146] Console: switching to colour STI console 160x64 [ 22.428956] Console: switching to colour frame buffer device 160x64 [ 22.706711] fb0: stifb 1280x1024-32 frame buffer device, HPA4071B, id: 2bcb015a, mmio: 0xfa100000 [ 22.821195] fb1: stifb 1024x768-8 frame buffer device, HPA4450AX1024, id: 2d08c0a7, mmio: 0xf4100000 [ 22.939347] fb2: stifb 800x600-8 frame buffer device, INTERNAL_EG_X800, id: 2d08c0a7, mmio: 0xf8100000 [ 23.057800] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 23.148120] printk: console [ttyS0] disabled [ 23.222647] 8:16:4: ttyS0 at MMIO 0xffd05800 (irq = 16, base_baud = 454545) is a 16550A [ 23.323729] printk: console [ttyS0] enabled [ 23.323729] printk: console [ttyS0] enabled [ 23.426230] printk: bootconsole [ttyB0] disabled [ 23.426230] printk: bootconsole [ttyB0] disabled [ 23.564155] 8:0:63: ttyS1 at MMIO 0xfff83800 (irq = 22, base_baud = 454545) is a 16550A [ 23.665426] serio: gsc-ps2-keyboard port at 0xffd08000 irq 21 @ 8:16:7 [ 23.744885] serio: gsc-ps2-mouse port at 0xffd08100 irq 21 @ 8:16:8 [ 23.823316] mousedev: PS/2 mouse device common for all mice [ 23.899162] rtc-generic rtc-generic: registered as rtc0 [ 23.962203] rtc-generic rtc-generic: setting system clock to 2020-11-01T12:41:37 UTC (1604234497) [ 24.069643] ledtrig-cpu: registered to indicate activity on CPUs [ 24.148121] NET: Registered protocol family 10 [ 24.783527] process '/usr/bin/kmod' started with executable stack [ 25.032159] Segment Routing with IPv6 [ 25.077209] mip6: Mobile IPv6 [ 25.113104] NET: Registered protocol family 17 [ 25.736459] mpls_gso: MPLS GSO support [ 25.782614] registered taskstats version 1 [ 25.831883] Loading compiled-in X.509 certificates [ 26.024485] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 26.129042] Loaded X.509 cert 'Debian Secure Boot Signer 2020: 00b55eb3b9' [ 26.212159] zswap: loaded using pool lzo/zbud [ 26.269407] Key type ._fscrypt registered [ 26.317562] Key type .fscrypt registered [ 26.364951] Key type fscrypt-provisioning registered [ 26.426027] AppArmor: AppArmor sha1 policy hashing enabled [ 26.492537] Unstable clock detected, switching default tracing clock to "global" [ 26.492537] If you want to keep using the local clock, then add: [ 26.492537] "trace_clock=local" [ 26.492537] on the kernel command line [ 30.687955] Freeing unused kernel memory: 652K [ 30.742369] Write protected read-only-after-init data: 33k [ 30.808033] Run /init as init process Loading, please wait... Starting version 246.6-1 [ 34.169556] lasi_82596: module verification failed: signature and/or required key missing - tainting kernel [ 34.689997] SCSI subsystem initialized [ 35.427955] 53c700: Version 2.8 By James.Bottomley@HansenPartnership.com [ 35.508022] scsi0: 53c710 rev 2 [ 36.548064] scsi host0: LASI SCSI 53c700 [ 36.598775] zalon_probe: Zalon version 1, IRQ 68 [ 36.654058] ncr53c720-0: rev 0xf irq 68 [ 36.760264] LASI 82596 driver - Revision: 1.30 [ 37.107604] Found i82596 at 0xffd07000, IRQ 18 [ 37.363830] ncr53c720-0: ID 7, Fast-10, Parity Checking, Differential [ 37.502096] eth0: 82596 at 0xffd07000, 08:00:09:ef:34:f5 IRQ 18. [ 37.867658] scsi host1: ncr53c8xx-3.4.3g [ 38.693183] scsi 0:0:1:0: CD-ROM PHILIPS PCA80SC V3-0 PQ: 0 ANSI: 2 [ 38.790724] scsi target0:0:1: Beginning Domain Validation [ 38.857695] scsi target0:0:1: asynchronous [ 38.921449] scsi target0:0:1: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 8) [ 39.011852] scsi target0:0:1: Domain Validation skipping write tests [ 39.087763] scsi target0:0:1: Ending Domain Validation [ 41.253021] scsi 1:0:6:0: Direct-Access SEAGATE ST32171W HP03 PQ: 0 ANSI: 2 [ 41.350676] scsi target1:0:6: Beginning Domain Validation [ 41.420978] scsi target1:0:6: asynchronous [ 41.485211] scsi target1:0:6: wide asynchronous [ 41.550995] scsi target1:0:6: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) [ 41.645041] scsi target1:0:6: Domain Validation skipping write tests [ 41.720929] scsi target1:0:6: Ending Domain Validation [ 44.376362] sr 0:0:1:0: Power-on or device reset occurred [ 44.450423] sr 0:0:1:0: [sr0] scsi-1 drive [ 44.499496] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 44.587784] sd 1:0:6:0: Power-on or device reset occurred [ 44.656648] sd 1:0:6:0: [sda] 4194685 512-byte logical blocks: (2.15 GB/2.00 GiB) [ 44.756185] sd 1:0:6:0: [sda] Write Protect is off [ 44.897133] sd 1:0:6:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA [ 45.092258] sda: sda1 sda2 sda3 < sda5 sda6 > [ 45.278343] sd 1:0:6:0: [sda] Attached SCSI disk [ 46.775267] random: crng init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.36 [/sbin/fsck.ext3 (1) -- /dev/sda5] fsck.ext3 -a -C0 /dev/sda5 /dev/sda5: clean, 53892/112000 files, 391192/447804 blocks done. [ 51.202057] EXT4-fs (sda5): mounting ext3 file system using the ext4 subsystem [ 51.426098] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 53.589038] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. INIT: version 2.96 booting Using makefile-style concurrent boot in runlevel S. Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 71.238711] parport_init_chip: initialize bidirectional-mode [ 71.593185] sd 1:0:6:0: Attached scsi generic sg0 type 0 [ 71.891502] parport0: PC-style at 0xffd02800, irq 19 [PCSPP,TRISTATE] [ 72.043814] sr 0:0:1:0: Attached scsi generic sg1 type 5 [ 80.021927] udisks-part-id(350): unaligned access to 0xf906194e at ip=0x00012bd3 [ 80.110570] udisks-part-id(350): unaligned access to 0xf9061952 at ip=0x00012be7 [ 80.206139] udisks-part-id(350): unaligned access to 0xf906195e at ip=0x00012bd3 [ 80.294759] udisks-part-id(350): unaligned access to 0xf9061962 at ip=0x00012be7 [ 80.404060] udisks-part-id(350): unaligned access to 0xf906196e at ip=0x00012bd3 done. Setting up keyboard layout...done. Activating swap...[ 93.069695] Adding 144548k swap on /dev/sda6. Priority:-2 extents:1 across:144548k FS done. [ 93.657377] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro Checking file systems...setterm: terminal vt102 does not support --msg /dev/sda2: clean, 19/64256 files, 35123/128520 blocks setterm: terminal vt102 does not support --msg done. Cleaning up temporary files... [ 102.689254] handle_unaligned: 91 callbacks suppressed [ 102.689308] udisks-part-id(697): unaligned access to 0xfae1898e at ip=0x00012bd3 [ 102.838095] udisks-part-id(697): unaligned access to 0xfae18992 at ip=0x00012be7 [ 102.984337] udisks-part-id(697): unaligned access to 0xfae1899e at ip=0x00012bd3 [ 103.072891] udisks-part-id(697): unaligned access to 0xfae189a2 at ip=0x00012be7 [ 103.288383] udisks-part-id(697): unaligned access to 0xfae189ae at ip=0x00012bd3 [ 104.098604] loop: module loaded /tmp. Loading kernel module lasi_82596. Loading kernel module loop. [ 108.518747] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 108.629624] EXT4-fs (sda2): mounted filesystem without journal. Opts: (null) Mounting local f[ 108.718327] ext2 filesystem being mounted at /boot supports timestamps until 2038 (0x7fffffff) ilesystems... done. Activating swapfile swap, if any...done. Cleaning up temporary files.... Starting Setting kernel variables: sysctl. [ 115.160319] audit: type=1400 audit(1604234588.696:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=887 comm="apparmor_parser" [ 115.667580] audit: type=1400 audit(1604234589.152:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=897 comm="apparmor_parser" [ 115.850269] audit: type=1400 audit(1604234589.156:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=897 comm="apparmor_parser" [ 116.369919] audit: type=1400 audit(1604234589.904:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=900 comm="apparmor_parser" [ 116.549399] audit: type=1400 audit(1604234589.904:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=900 comm="apparmor_parser" [ 116.726663] audit: type=1400 audit(1604234589.904:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=900 comm="apparmor_parser" Starting: AppArmorLoading AppArmor profiles...done. . Configuring network interfaces...ifup: interface eth0 already configured done. Starting RPC port mapper daemon: rpcbind. [ 122.460698] RPC: Registered named UNIX socket transport module. [ 122.531477] RPC: Registered udp transport module. [ 122.587564] RPC: Registered tcp transport module. [ 122.643672] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 123.097210] FS-Cache: Loaded Starting NFS common utilities: statd [ 124.195474] FS-Cache: Netfs 'nfs' registered for caching [ 125.225129] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). idmapd. Cleaning up temporary files.... Setting console screen modes. Rsetterm: terminal vt102 does not support --blank setterm: cannot (un)set powersave mode: Inappropriate ioctl for device Skipping font and keymap setup (handled by console-setup). Setting up X socket directories... /tmp/.X11-unix /tmp/.ICE-unix . INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Setting up console font and keymap...done. Starting NFS common utilities: statd idmapd. Starting enhanced syslogd: rsyslogd. Starting anac(h)ronistic cron: anacron. Starting deferred execution scheduler: atd. Starting automount... . Starting system message bus: dbus. Starting periodic command scheduler: cron. Loading cpufreq kernel modules...done (none). CPUFreq Utilities: Setting ondemand CPUFreq governor...disabled, governor not available...done. Not starting NFS kernel daemon: no exports. ... (warning). Not starting internet superserver: no services enabled. Starting MTA: exim4. Starting OpenBSD Secure Shell server: sshd. Debian GNU/Linux bullseye/sid b160 ttyS0 b160 login: