C3700 (A6057B Revision B) [Firmware 2.0] 750mhz PA8700 (PCX-W2) 1.2gig of ram 18gig SCA80 SCSI HDD HP FX-10pro Video card (A1299B Visualize-FX10b Pro PCI Graphics Board - 128MB DDR SDRAM Memory) And all standard onboard devices. Linux pabox 2.6.16.18-pa11 #1 Sat May 27 22:53:59 EST 2006 parisc PA8700 (PCX-W2) 9000/785/C3700 GNU/Linux processor : 0 cpu family : PA-RISC 2.0 cpu : PA8700 (PCX-W2) cpu MHz : 750.000000 model : 9000/785/C3700 model name : Allegro W2 hversion : 0x00005dc0 sversion : 0x00000481 I-cache : 768 KB D-cache : 1536 KB (WB, 0-way associative) ITLB entries : 240 DTLB entries : 240 - shared with ITLB BTLB : not supported bogomips : 1497.49 software id : 2006400178 Linux version 2.6.16.18-pa11 (root@pabox) (gcc version 3.4.5 (Gentoo Linux 3.4.5)) #2 Sun May 28 17:10:44 EST 2006 FP[0] enabled: Rev 1 Model 19 The 64-bit Kernel has started... Initialized PDC Console for debugging. Determining PDC firmware type: System Map. model 00005dc0 00000481 00000000 00000002 77973cb2 100000f0 00000008 000000b2 000000b2 vers 00000203 CPUID vers 19 rev 7 (0x00000267) capabilities 0x7 model 9000/785/C3700 Total Memory: 1280 MB On node 0 totalpages: 327680 DMA zone: 327680 pages, LIFO batch:31 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 LCD display at fffffff0f05d0008,fffffff0f05d0000 registered Built 1 zonelists Kernel command line: root=/dev/sda4 console=tty0 sti=10/6/2/0 sti_font=VGA8x16 palo_kernel=2/c3700-64 PID hash table entries: 4096 (order: 12, 131072 bytes) Console: colour dummy device 128x48 Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Memory: 1310720k available Calibrating delay loop... 1490.94 BogoMIPS (lpj=745472) Mount-cache hash table entries: 256 NET: Registered protocol family 16 EISA bus registered Searching for devices... Found devices: 1. Astro BC Runway Port at 0xfffffffffed00000 [10] { 12, 0x0, 0x582, 0x0000b } 2. Elroy PCI Bridge at 0xfffffffffed30000 [10/0] { 13, 0x0, 0x782, 0x0000a } 3. Elroy PCI Bridge at 0xfffffffffed32000 [10/1] { 13, 0x0, 0x782, 0x0000a } 4. Elroy PCI Bridge at 0xfffffffffed38000 [10/4] { 13, 0x0, 0x782, 0x0000a } 5. Elroy PCI Bridge at 0xfffffffffed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a } 6. Allegro W2 at 0xfffffffffffa0000 [32] { 0, 0x0, 0x5dc, 0x00004 } 7. Memory at 0xfffffffffed10200 [49] { 1, 0x0, 0x09c, 0x00009 } CPU(s): 1 x PA8700 (PCX-W2) at 750.000000 MHz Whole cache flush 45271624 cycles, flushing 7769232 bytes 1578612 cycles Setting cache flush threshold to d47c3c0 (1 CPUs online) SBA found Astro 2.1 at 0xfffffffffed00000 LBA version TR4.0 (0x5) found at 0xfffffffffed30000 PCI: Enabled native mode for NS87415 (pif=0x8f) LBA version TR4.0 (0x5) found at 0xfffffffffed32000 LBA version TR4.0 (0x5) found at 0xfffffffffed38000 LBA version TR4.0 (0x5) found at 0xfffffffffed3c000 iosapic: hpa not registered for 0000:03:02.0 SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub unwind_init: start = 0x10599d80, end = 0x105ce370, entries = 13407 Performance monitoring counters enabled for Allegro W2 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 67) SuperIO: Serial port 1 at 0x3f8 SuperIO: Serial port 2 at 0x2f8 SuperIO: Parallel port at 0x378 SuperIO: Floppy controller at 0x3f0 SuperIO: ACPI at 0x7e0 SuperIO: USB regulator enabled pci_hotplug: PCI Hot Plug PCI Core version: 0.5 PDC Stable Storage facility v0.22 Soft power switch enabled, polling @ 0xfffffff0f0400804. STI GSC/PCI core graphics driver Version 0.9a STI PCI graphic ROM found at fffffffff7000000 (2048 kB), fb at fffffffffa000000 (32 MB) id 35acda30-9a02587, conforms to spec rev. 8.0d graphics card name: A1299B sticon: Initializing STI text console. Console: switching to colour STI console 160x64 stifb: 'A1299B' (id: 0x35acda30) not supported. Generic RTC Driver v1.07 HP SDC: No SDC found. HP SDC MLC: Registering the System Domain Controller's HIL MLC. HP SDC MLC: Request for raw HIL ISR hook denied Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A isa bounce pool size: 16 pages RAMDISK driver initialized: 16 RAM disks of 6144K size 1024 blocksize loop: loaded (max 8 devices) orinoco 0.15rc3 (David Gibson , Pavel Roskin , et al) orinoco_cs 0.15rc3 (David Gibson , Pavel Roskin , et al) spectrum_cs 0.15rc3 (Pavel Roskin , David Gibson , et al) Linux Tulip driver version 1.1.13 (December 15, 2004) tulip0: no phy info, aborting mtable build tulip0: MII transceiver #1 config 1000 status 782d advertising 01e1. eth0: Digital DS21142/DS21143 Tulip rev 65 at 8000000000001000, 00:30:6E:2B:8A:16, IRQ 65. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NS87415: IDE controller at PCI slot 0000:00:0e.0 NS87415: chipset revision 3 NS87415: 100% native mode on irq 7 ide0: BM-DMA at 0x0a00-0x0a07, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0x0a08-0x0a0f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: HL-DT-ST RW/DVD GCC-4521B, ATAPI CD/DVD-ROM drive ide0 at 0xf00-0xf07,0xe02 on irq 7 Probing IDE interface ide1... Probing IDE interface ide1... hda: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 sym0: <896> rev 0x7 at pci 0000:00:0f.0 irq 68 sym0: PA-RISC Firmware, ID 7, Fast-40, SE, parity checking sym0: SCSI BUS has been reset. sym0: SCSI BUS mode change from SE to SE. sym0: SCSI BUS has been reset. scsi0 : sym-2.2.2 sym1: <896> rev 0x7 at pci 0000:00:0f.1 irq 68 sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking sym1: SCSI BUS has been reset. scsi1 : sym-2.2.2 Vendor: HP 18.2G Model: ST318406LC Rev: HP03 Type: Direct-Access ANSI SCSI revision: 02 target1:0:6: tagged command queuing enabled, command queue depth 16. target1:0:6: Beginning Domain Validation target1:0:6: asynchronous target1:0:6: wide asynchronous target1:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31) target1:0:6: Domain Validation skipping write tests target1:0:6: Ending Domain Validation st: Version 20050830, fixed bufsize 32768, s/g segs 256 SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB) sda: Write Protect is off sda: Mode Sense: 9f 00 10 08 SCSI device sda: drive cache: write back w/ FUA SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB) sda: Write Protect is off sda: Mode Sense: 9f 00 10 08 SCSI device sda: drive cache: write back w/ FUA sda: sda1 sda2 sda3 sda4 sd 1:0:6:0: Attached scsi disk sda sd 1:0:6:0: Attached scsi generic sg0 type 0 usbmon: debugfs is not available ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd 0000:00:0e.2: OHCI Host Controller ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:0e.2: irq 1, io mem 0xfffffffff4007000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected USB Universal Host Controller Interface driver v2.3 usb 1-1: new low speed USB device using ohci_hcd and address 2 usb 1-1: configuration #1 chosen from 1 choice usb 1-2: new low speed USB device using ohci_hcd and address 3 usb 1-2: configuration #1 chosen from 1 choice usbcore: registered new driver libusual input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input0 input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:0e.2-1 input: Dell Dell USB Keyboard as /class/input/input1 input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:0e.2-2 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: measuring checksumming speed 8regs : 3796.000 MB/sec 8regs_prefetch: 2480.000 MB/sec 32regs : 3496.000 MB/sec 32regs_prefetch: 2600.000 MB/sec raid5: using function: 8regs (3796.000 MB/sec) raid6: int64x1 730 MB/s raid6: int64x2 882 MB/s raid6: int64x4 968 MB/s raid6: int64x8 824 MB/s raid6: using algorithm int64x4 (968 MB/s) md: raid6 personality registered for level 6 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20 2006 UTC). ALSA device list: #0: Analog Devices AD1889 at 0xfffffffff400c000 irq 66 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 540k freed Adding 15677432k swap on /dev/sda3. Priority:-1 extents:1 across:15677432k EXT3 FS on sda4, internal journal eth0: Setting full-duplex based on MII#1 link partner capability of 45e1. eth0: no IPv6 routers present Linux version 2.6.16.18-pa11 (root@livecd) (gcc version 3.3.6 (Gentoo 3.3.6, pie-8.7.8)) #1 Sat May 27 22:53:59 EST 2006 FP[0] enabled: Rev 1 Model 19 The 32-bit Kernel has started... Initialized PDC Console for debugging. Determining PDC firmware type: System Map. model 00005dc0 00000481 00000000 00000002 77973cb2 100000f0 00000008 000000b2 000000b2 vers 00000203 CPUID vers 19 rev 7 (0x00000267) capabilities 0x7 model 9000/785/C3700 Total Memory: 1280 MB On node 0 totalpages: 327680 DMA zone: 327680 pages, LIFO batch:31 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 LCD display at f05d0008,f05d0000 registered Built 1 zonelists Kernel command line: root=/dev/sda4 console=tty0 sti=10/6/2/0 sti_font=VGA8x16 palo_kernel=2/c3700 PID hash table entries: 4096 (order: 12, 65536 bytes) Console: colour dummy device 128x48 Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes) Inode-cache hash table entries: 131072 (order: 7, 524288 bytes) Memory: 1310720k available Calibrating delay loop... 1497.49 BogoMIPS (lpj=7487488) Mount-cache hash table entries: 512 NET: Registered protocol family 16 EISA bus registered Searching for devices... Found devices: 1. Astro BC Runway Port at 0xfed00000 [10] { 12, 0x0, 0x582, 0x0000b } 2. Elroy PCI Bridge at 0xfed30000 [10/0] { 13, 0x0, 0x782, 0x0000a } 3. Elroy PCI Bridge at 0xfed32000 [10/1] { 13, 0x0, 0x782, 0x0000a } 4. Elroy PCI Bridge at 0xfed38000 [10/4] { 13, 0x0, 0x782, 0x0000a } 5. Elroy PCI Bridge at 0xfed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a } 6. Allegro W2 at 0xfffa0000 [32] { 0, 0x0, 0x5dc, 0x00004 } 7. Memory at 0xfed10200 [49] { 1, 0x0, 0x09c, 0x00009 } CPU(s): 1 x PA8700 (PCX-W2) at 750.000000 MHz Whole cache flush 1120866 cycles, flushing 6133832 bytes 1226690 cycles Setting cache flush threshold to a60 (1 CPUs online) SBA found Astro 2.1 at 0xfed00000 LBA version TR4.0 (0x5) found at 0xfed30000 PCI: Enabled native mode for NS87415 (pif=0x8f) LBA version TR4.0 (0x5) found at 0xfed32000 LBA version TR4.0 (0x5) found at 0xfed38000 LBA version TR4.0 (0x5) found at 0xfed3c000 iosapic: hpa not registered for 0000:03:02.0 SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub unwind_init: start = 0x104ff6d0, end = 0x1053ce70, entries = 15738 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 67) SuperIO: Serial port 1 at 0x3f8 SuperIO: Serial port 2 at 0x2f8 SuperIO: Parallel port at 0x378 SuperIO: Floppy controller at 0x3f0 SuperIO: ACPI at 0x7e0 SuperIO: USB regulator enabled pci_hotplug: PCI Hot Plug PCI Core version: 0.5 PDC Stable Storage facility v0.22 Soft power switch enabled, polling @ 0xf0400804. STI GSC/PCI core graphics driver Version 0.9a STI PCI graphic ROM found at f7000000 (2048 kB), fb at fa000000 (32 MB) id 35acda30-9a02587, conforms to spec rev. 8.0d graphics card name: A1299B sticon: Initializing STI text console. Console: switching to colour STI console 160x64 stifb: 'A1299B' (id: 0x35acda30) not supported. Generic RTC Driver v1.07 HP SDC: No SDC found. HP SDC MLC: Registering the System Domain Controller's HIL MLC. HP SDC MLC: Request for raw HIL ISR hook denied Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 6144K size 1024 blocksize loop: loaded (max 8 devices) orinoco 0.15rc3 (David Gibson , Pavel Roskin , et al) orinoco_cs 0.15rc3 (David Gibson , Pavel Roskin , et al) spectrum_cs 0.15rc3 (Pavel Roskin , David Gibson , et al) Linux Tulip driver version 1.1.13 (December 15, 2004) tulip0: no phy info, aborting mtable build tulip0: MII transceiver #1 config 1000 status 782d advertising 01e1. eth0: Digital DS21142/DS21143 Tulip rev 65 at 80001000, 00:30:6E:2B:8A:16, IRQ 65. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NS87415: IDE controller at PCI slot 0000:00:0e.0 NS87415: chipset revision 3 NS87415: 100% native mode on irq 7 ide0: BM-DMA at 0x0a00-0x0a07, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0x0a08-0x0a0f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: HL-DT-ST RW/DVD GCC-4521B, ATAPI CD/DVD-ROM drive ide0 at 0xf00-0xf07,0xe02 on irq 7 Probing IDE interface ide1... Probing IDE interface ide1... hda: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 sym0: <896> rev 0x7 at pci 0000:00:0f.0 irq 68 sym0: PA-RISC Firmware, ID 7, Fast-40, SE, parity checking sym0: SCSI BUS has been reset. sym0: SCSI BUS mode change from SE to SE. sym0: SCSI BUS has been reset. scsi0 : sym-2.2.2 sym1: <896> rev 0x7 at pci 0000:00:0f.1 irq 68 sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking sym1: SCSI BUS has been reset. scsi1 : sym-2.2.2 Vendor: HP 18.2G Model: ST318406LC Rev: HP03 Type: Direct-Access ANSI SCSI revision: 02 target1:0:6: tagged command queuing enabled, command queue depth 16. target1:0:6: Beginning Domain Validation target1:0:6: asynchronous target1:0:6: wide asynchronous target1:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31) target1:0:6: Domain Validation skipping write tests target1:0:6: Ending Domain Validation st: Version 20050830, fixed bufsize 32768, s/g segs 256 SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB) sda: Write Protect is off sda: Mode Sense: 9f 00 10 08 /proc/iomem 00000000-4fffffff : System RAM 00000000-000009ff : PDC data (Page Zero) 00100000-0058efff : Kernel code 0058f000-00868c8f : Kernel data fffffff0f05d0000-fffffff0f05d0000 : lcd_data fffffff0f05d0008-fffffff0f05d0008 : lcd_cmd fffffffff4000000-fffffffff47fffff : PCI00 LMMIO fffffffff4000000-fffffffff4001fff : sym53c8xx fffffffff4002000-fffffffff4003fff : sym53c8xx fffffffff4004000-fffffffff40043ff : sym53c8xx fffffffff4005000-fffffffff40053ff : sym53c8xx fffffffff4007000-fffffffff4007fff : ohci_hcd fffffffff4008000-fffffffff40083ff : tulip fffffffff4009000-fffffffff400900f : AD1889 fffffffff400a000-fffffffff400a00f : AD1889 fffffffff400b000-fffffffff400b00f : AD1889 fffffffff400c000-fffffffff400c1ff : AD1889 fffffffff4800000-fffffffff4ffffff : PCI01 LMMIO fffffffff6000000-fffffffff67fffff : PCI02 LMMIO fffffffff7000000-fffffffff77fffff : PCI03 LMMIO fffffffffa000000-fffffffffbffffff : PCI03 ELMMIO fffffffffed00000-fffffffffed00fff : 10 fffffffffed30000-fffffffffed30fff : 10:0 fffffffffed32000-fffffffffed32fff : 10:1 fffffffffed38000-fffffffffed38fff : 10:4 fffffffffed3c000-fffffffffed3cfff : 10:6 fffffffffef00000-fffffffffeffffff : Astro Intr Ack fffffffffff80000-fffffffffffaffff : Central Bus fffffffffffa0000-fffffffffffa0fff : 32 fffffffffffb0000-fffffffffffdffff : Local Broadcast fffffffffffe0000-ffffffffffffffff : Global Broadcast /proc/ioports 00000000-00001fff : PCI00 Ports 00000020-0000003e : pic1 000000a0-000000be : pic2 000007e0-000007fe : acpi 00000800-000008ff : sym53c8xx 00000900-000009ff : sym53c8xx 00000a00-00000a07 : ide0 00000a08-00000a0f : ide1 00000e02-00000e02 : ide0 00000f00-00000f07 : ide0 00001000-0000107f : tulip 00012000-00013fff : PCI01 Ports 00028000-00029fff : PCI02 Ports 0003c000-0003dfff : PCI03 Ports