Linux version 2.6.12-10-hppa64-smp (buildd@bld-4) (gcc version 3.4.5 20050809 (prerelease) (Ubuntu 3.4.4-6ubuntu8)) #1 SMP Thu Dec 22 17:34:30 UTC 2005
FP[0] enabled: Rev 1 Model 16
The 64-bit Kernel has started...
Initialized PDC Console for debugging.
Determining PDC firmware type: System Map.
model 00005d40 00000491 00000000 00000002 77390fff 100000f0 00000008 000000b2 000000b2
vers  00000301
CPUID vers 17 rev 11 (0x0000022b)
capabilities 0x3
model 9000/785/J6000
Memory Ranges:
 0) Start 0x0000000000000000 End 0x00000000efffffff Size   3840 MB
 1) Start 0x0000000100000000 End 0x00000001ffffffff Size   4096 MB
 2) Start 0x00000010f0000000 End 0x00000010ffffffff Size    256 MB
Total Memory: 8192 MB
initrd: 4fb1f000-4ffee000
initrd: reserving 3fb1f000-3ffee000 (mem_max 200000000)
On node 0 totalpages: 983040
  DMA zone: 983040 pages, LIFO batch:31
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
On node 1 totalpages: 1048576
  DMA zone: 1048576 pages, LIFO batch:31
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
On node 2 totalpages: 65536
  DMA zone: 65536 pages, LIFO batch:31
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
LCD display at fffffff0f05d0008,fffffff0f05d0000 registered
SMP: bootstrap CPU ID is 0
Built 3 zonelists
Kernel command line: root=/dev/sda3 console=ttyS0 TERM=vt102 palo_kernel=1/vmlinux
PID hash table entries: 4096 (order: 12, 131072 bytes)
Console: colour dummy device 160x64
Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Memory: 8388608k available
Calibrating delay loop... 1097.72 BogoMIPS (lpj=548864)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 256
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Brought up 1 CPUs
CPU0 attaching sched-domain:
 domain 0: span 00000001
  groups: 00000001
NET: Registered protocol family 16
EISA bus registered
Searching for devices...
Found devices:
1. Astro BC Runway Port at 0xfffffffffed00000 [10] { 12, 0x0, 0x582, 0x0000b }
2. Elroy PCI Bridge at 0xfffffffffed30000 [10/0] { 13, 0x0, 0x782, 0x0000a }
3. Elroy PCI Bridge at 0xfffffffffed34000 [10/2] { 13, 0x0, 0x782, 0x0000a }
4. Elroy PCI Bridge at 0xfffffffffed38000 [10/4] { 13, 0x0, 0x782, 0x0000a }
5. Elroy PCI Bridge at 0xfffffffffed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a }
6. Duet W+ at 0xfffffffffffa0000 [32] { 0, 0x0, 0x5d4, 0x00004 }
7. Duet W+ at 0xfffffffffffa2000 [34] { 0, 0x0, 0x5d4, 0x00004 }
8. Memory at 0xfffffffffed10200 [49] { 1, 0x0, 0x00a, 0x00009 }
CPU0 attaching sched-domain:
 domain 0: does not load-balance
Releasing cpu 1 now, hpa=fffffffffffa2000
FP[1] enabled: Rev 1 Model 16
CPU0 attaching sched-domain:
 domain 0: span 00000003
  groups: 00000001 00000002
CPU1 attaching sched-domain:
 domain 0: span 00000003
  groups: 00000002 00000001
CPU(s): 2 x PA8600 (PCX-W+) at 552.000000 MHz
Whole cache flush 307586 cycles, flushing 274929872 bytes 41408815 cycles
Setting cache flush threshold to 1f2980 (2 CPUs online)
SBA found Astro 2.1 at 0xfffffffffed00000
LBA version TR4.0 (0x5) found at 0xfffffffffed30000
PCI: Enabled native mode for NS87415 (pif=0x8f)
LBA version TR4.0 (0x5) found at 0xfffffffffed34000
LBA version TR4.0 (0x5) found at 0xfffffffffed38000
LBA version TR4.0 (0x5) found at 0xfffffffffed3c000
SCSI subsystem initialized
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
unwind_init: start = 0x10422d60, end = 0x10443210, entries = 8267
Performance monitoring counters enabled for Duet W+
audit: initializing netlink socket (disabled)
audit: initialized
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 68) 
SuperIO: Serial port 1 at 0x3f8
SuperIO: Serial port 2 at 0x2f8
SuperIO: Parallel port at 0x378
SuperIO: Floppy controller at 0x3f0
SuperIO: ACPI at 0x7e0
SuperIO: USB regulator enabled
Soft power switch enabled, polling @ 0xfffffff0f0400804.
STI GSC/PCI core graphics driver Version 0.9a
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 13 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP: routing cache hash table of 32768 buckets, 512Kbytes
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4924KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: Badness in smp_call_function at arch/parisc/kernel/smp.c:340
Backtrace:
 [<0000000010114e80>] dump_stack+0x18/0x28
 [<000000001011f7e0>] smp_call_function+0x438/0x440
 [<0000000010113b14>] flush_data_cache+0x34/0x60
 [<0000000010112ac4>] free_initmem+0x94/0x3c8
 [<0000000010112084>] init+0x81c/0x880
 [<000000001010647c>] ret_from_kernel_thread+0x24/0x40

388k freed
sym0: <896> rev 0x4 at pci 0000:00:0f.0 irq 69
sym0: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.1
sym1: <896> rev 0x4 at pci 0000:00:0f.1 irq 69
sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
sym1: SCSI BUS has been reset.
scsi1 : sym-2.2.1
  Vendor: SEAGATE   Model: ST318451LC        Rev: HP01
  Type:   Direct-Access                      ANSI SCSI revision: 03
 target1:0:5: tagged command queuing enabled, command queue depth 16.
 target1:0:5: Beginning Domain Validation
 target1:0:5: asynchronous.
WIDTH IS 1
 target1:0:5: wide asynchronous.
 target1:0:5: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
 target1:0:5: Ending Domain Validation
sym2: <896> rev 0x1 at pci 0000:03:03.0 irq 71
sym2: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
sym2: SCSI BUS has been reset.
scsi2 : sym-2.2.1
sym3: <896> rev 0x1 at pci 0000:03:03.1 irq 72
sym3: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
sym3: SCSI BUS has been reset.
scsi3 : sym-2.2.1
SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB)
SCSI device sda: drive cache: write through
SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB)
SCSI device sda: drive cache: write through
 /dev/scsi/host1/bus0/target5/lun0: p1 p2 p3
Attached scsi disk sda at scsi1, channel 0, id 5, lun 0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Adding 979956k swap on /dev/sda2.  Priority:-1 extents:1
EXT3 FS on sda3, internal journal
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Tulip driver version 1.1.13 (December 15, 2004)
tulip0: no phy info, aborting mtable build
tulip0:  MII transceiver #1 config 1000 status 782d advertising 01e1.
eth0: Digital DS21142/DS21143 Tulip rev 65 at 8000000000001000, 00:10:83:FF:B7:30, IRQ 66.
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 80 td 96
ohci_hcd 0000:00:0e.2: National Semiconductor Corporation USB Controller
ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0e.2: irq 1, io mem 0xfffffffff4007000
ohci_hcd 0000:00:0e.2: Using NSC SuperIO setup
ohci_hcd 0000:00:0e.2: resetting from state 'reset', control = 0x0
ohci_hcd 0000:00:0e.2: OHCI controller state
ohci_hcd 0000:00:0e.2: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:0e.2: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:0e.2: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:0e.2: intrstatus 0x00000000
ohci_hcd 0000:00:0e.2: intrenable 0x8000001a MIE UE RD WDH
ohci_hcd 0000:00:0e.2: fminterval a7782edf
ohci_hcd 0000:00:0e.2: hcca frame #0000
ohci_hcd 0000:00:0e.2: roothub.a 00001003 POTPGT=0 NOCP NDP=3
ohci_hcd 0000:00:0e.2: roothub.b 000e0000 PPCM=000e DR=0000
ohci_hcd 0000:00:0e.2: roothub.status 00008000 DRWE
ohci_hcd 0000:00:0e.2: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:0e.2: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:0e.2: roothub.portstatus [2] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: National Semiconductor Corporation USB Controller
usb usb1: Manufacturer: Linux 2.6.12-10-hppa64-smp ohci_hcd
usb usb1: SerialNumber: 0000:00:0e.2
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: no over-current protection
hub 1-0:1.0: power on to power good time: 0ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
ohci_hcd 0000:00:0e.2: created debug files
hub 1-0:1.0: state 5 ports 3 chg 0000 evt 0000
tg3.c:v3.31 (June 8, 2005)
eth1: Tigon3 [partno(A6825-60101) rev 0105 PHY(5701)] (PCI:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:30:6e:4c:37:6e
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0] 
eth1: dma_rwctrl[76ff2d0f]
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
NET: Registered protocol family 10
Disabled Privacy Extensions on device 00000000104ddeb8(lo)
IPv6 over IPv4 tunneling driver
eth0: Setting full-duplex based on MII#1 link partner capability of 41e1.
eth0: no IPv6 routers present
Clock: inserting leap second 23:59:60 UTC
scsi: unknown opcode 0x1d

cat /proc/cpuinfo
processor       : 0
cpu family      : PA-RISC 2.0
cpu             : PA8600 (PCX-W+)
cpu MHz         : 552.000000
model           : 9000/785/J6000
model name      : Duet W+
hversion        : 0x00005d40
sversion        : 0x00000491
I-cache         : 512 KB
D-cache         : 1024 KB (WB, 0-way associative)
ITLB entries    : 160
DTLB entries    : 160 - shared with ITLB
bogomips        : 1097.72
software id     : 2000228351

processor       : 1
cpu family      : PA-RISC 2.0
cpu             : PA8600 (PCX-W+)
cpu MHz         : 552.000000
model           : 9000/785/J6000
model name      : Duet W+
hversion        : 0x00005d40
sversion        : 0x00000491
I-cache         : 512 KB
D-cache         : 1024 KB (WB, 0-way associative)
ITLB entries    : 160
DTLB entries    : 160 - shared with ITLB
bogomips        : 1097.72
software id     : 2000228351

cat /proc/interrupts
           CPU0       CPU1
  1:          0          0         SuperIO  ohci_hcd:usb1
  3:       1606          0         SuperIO  serial
 64:  497738236  497732193             CPU  timer
 65:      58579      71356             CPU  IPI
 66:     137332          0  IO-SAPIC-level  eth0
 68:       1606          0  IO-SAPIC-level  SuperIO
 69:          0      95381  IO-SAPIC-level  sym53c8xx, sym53c8xx
 71:          0         32  IO-SAPIC-level  sym53c8xx
 72:         33          0  IO-SAPIC-level  sym53c8xx

cat /proc/iomem
00000000-efffffff : System RAM
  00000000-000009ff : PDC data (Page Zero)
  00100000-00419fff : Kernel code
  0041a000-006318cf : Kernel data
100000000-1ffffffff : System RAM
10f0000000-10ffffffff : System RAM
fffffff0f05d0000-fffffff0f05d0000 : lcd_data
fffffff0f05d0008-fffffff0f05d0008 : lcd_cmd
fffffffff4000000-fffffffff47fffff : PCI00 LMMIO
  fffffffff4000000-fffffffff4001fff : sym53c8xx
  fffffffff4002000-fffffffff4003fff : sym53c8xx
  fffffffff4004000-fffffffff40043ff : sym53c8xx
  fffffffff4005000-fffffffff40053ff : sym53c8xx
  fffffffff4007000-fffffffff4007fff : ohci_hcd
  fffffffff4008000-fffffffff40083ff : tulip
fffffffff5000000-fffffffff57fffff : PCI01 LMMIO
fffffffff6000000-fffffffff67fffff : PCI02 LMMIO
  fffffffff6000000-fffffffff600ffff : tg3
fffffffff7000000-fffffffff77fffff : PCI03 LMMIO
  fffffffff7000000-fffffffff7001fff : sym53c8xx
  fffffffff7002000-fffffffff7003fff : sym53c8xx
  fffffffff7004000-fffffffff70043ff : sym53c8xx
  fffffffff7005000-fffffffff70053ff : sym53c8xx
fffffffffed00000-fffffffffed00fff : SBA
fffffffffed30000-fffffffffed30fff : LBA
fffffffffed34000-fffffffffed34fff : LBA
fffffffffed38000-fffffffffed38fff : LBA
fffffffffed3c000-fffffffffed3cfff : LBA
fffffffffef00000-fffffffffeffffff : Astro Intr Ack
fffffffffff80000-fffffffffffaffff : Central Bus
  fffffffffffa0000-fffffffffffa0fff : CPU
  fffffffffffa2000-fffffffffffa2fff : CPU
fffffffffffb0000-fffffffffffdffff : Local Broadcast
fffffffffffe0000-ffffffffffffffff : Global Broadcast

cat /proc/ioports
00000000-00001fff : PCI00 Ports
  00000020-0000003e : pic1
  000000a0-000000be : pic2
  000007e0-000007fe : acpi
  00000800-000008ff : sym53c8xx
  00000900-000009ff : sym53c8xx
  00001000-0000107f : tulip
00014000-00015fff : PCI01 Ports
00028000-00029fff : PCI02 Ports
0003c000-0003dfff : PCI03 Ports
  0003c000-0003c0ff : sym53c8xx
  0003c100-0003c1ff : sym53c8xx