Firmware Version 1.7 Duplex Console IO Dependent Code (IODC) revision 1 ------------------------------------------------------------------------------ (c) Copyright 1995-2000, Hewlett-Packard Company, All rights reserved ------------------------------------------------------------------------------ Processor Speed State Coprocessor State I/D Cache --------- -------- --------------------- ----------------- ------------- 0 750 MHz Active Functional 768 kB/1536 kB 1 750 MHz Idle Functional 768 kB/1536 kB Central Bus Speed: 120 MHz Available memory: 8589934592 bytes Good memory required: 25698304 bytes Primary boot path: FWSCSI.6.0 Alternate boot path: SCSI.6.0 Console path: GRAPHICS(2) Keyboard path: USB Processor is starting auto boot process. Booting... Boot IO Dependent Code (IODC) revision 0 HARD Booted. palo ipl 2.16 https://parisc.wiki.kernel.org - Fri, 01 Apr 2022 21:16:22 +0000 Decompressing Linux... done. Booting the kernel. [ 0.000000] Linux version 6.1.0-1-parisc64 (debian-kernel@lists.debian.org) (hppa64-linux-gnu-gcc-12 (GCC) 12.2.0, GNU ld (GNU Binutils for Debian) 2.39.90.20230104) #1 SMP Debian 6.1.4-1 (2023-01-07) [ 0.000000] FP[0] enabled: Rev 1 Model 19 [ 0.000000] The 64-bit Kernel has started... [ 0.000000] Kernel default page size is 4 KB. Huge pages enabled with 1 MB physical and 2 MB virtual size. [ 0.000000] Determining PDC firmware type: System Map. [ 0.000000] model 00005dd0 00000491 00000000 00000002 77a95f12 100000f0 00000008 000000b2 000000b2 [ 0.000000] vers 00000203 [ 0.000000] CPUID vers 19 rev 7 (0x00000267) [ 0.000000] capabilities 0x7 [ 0.000000] model 9000/785/J6700 [ 0.000000] Memory Ranges: [ 0.000000] 0) Start 0x0000000000000000 End 0x00000000efffffff Size 3840 MB [ 0.000000] 1) Start 0x0000000100000000 End 0x00000001ffffffff Size 4096 MB [ 0.000000] 2) Start 0x00000010f0000000 End 0x00000010ffffffff Size 256 MB [ 0.000000] Total Memory: 8192 MB [ 0.000000] initrd: 7e3af000-7ffedda1 [ 0.000000] initrd: reserving 3e3af000-3ffedda1 (mem_max 200000000) [ 0.000000] PDT: type PDT_PDC, size 50, entries 0, status 2, dbe_loc 0xffffffffffffffff, good_mem 24 MB [ 0.000000] PDT: Firmware reports all memory OK. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x00010fffffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x00000000efffffff] [ 0.000000] node 0: [mem 0x0000000100000000-0x00000001ffffffff] [ 0.000000] node 0: [mem 0x00000010f0000000-0x00000010ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000010ffffffff] [ 0.000000] LCD display at fffffff0f05d0008,fffffff0f05d0000 registered [ 0.000000] percpu: Embedded 45 pages/cpu s146528 r8192 d29600 u184320 [ 0.000000] SMP: bootstrap CPU ID is 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2064384 [ 0.000000] Kernel command line: root=LABEL=ROOT280a root2=/dev/sdb5 HOME=/ rootfstype=ext4 panic_timeout=60 panic=-1 console=ttyS0 TERM=vt102 palo_kernel=2/vmlinuz-6.1.0-1-parisc64 earlycon=pdc [ 0.000000] earlycon: pdc0 at MMIO32be 0x0000000000000000 (options '') [ 0.000000] printk: bootconsole [pdc0] enabled [ 0.000000] Unknown kernel command line parameters "root2=/dev/sdb5 panic_timeout=60 palo_kernel=2/vmlinuz-6.1.0-1-parisc64", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 1016K/8388608K available (14304K kernel code, 5659K rwdata, 1971K rodata, 2048K init, 824K bss, 215716K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=16, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] ftrace: allocating 28084 entries in 110 pages [ 0.000000] ftrace: allocated 110 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 128 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000004] sched_clock: 64 bits at 750MHz, resolution 1ns, wraps every 4398046511103ns [ 0.105973] Console: colour dummy device 160x64 [ 0.165672] Calibrating delay loop... 1494.01 BogoMIPS (lpj=2988032) [ 0.269649] pid_max: default: 32768 minimum: 301 [ 0.334251] LSM: Security Framework initializing [ 0.393775] landlock: Up and running. [ 0.441647] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.530022] AppArmor: AppArmor initialized [ 0.581653] TOMOYO Linux initialized [ 0.630363] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.729994] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.842219] cblist_init_generic: Setting adjustable number of callback queues. [ 0.933649] cblist_init_generic: Setting shift to 3 and lim to 1. [ 1.017686] cblist_init_generic: Setting shift to 3 and lim to 1. [ 1.097805] TOC handler registered [ 1.141834] rcu: Hierarchical SRCU implementation. [ 1.205652] rcu: Max phase no-delay instances is 1000. [ 1.283154] smp: Bringing up secondary CPUs ... [ 1.341663] smp: Brought up 1 node, 1 CPU [ 2.265730] node 0 deferred pages initialised in 872ms [ 2.336632] devtmpfs: initialized [ 2.382725] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 2.509893] futex hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 2.604581] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 2.682062] audit: initializing netlink subsys (disabled) [ 2.754978] thermal_sys: Registered thermal governor 'fair_share' [ 2.754993] thermal_sys: Registered thermal governor 'bang_bang' [ 2.833674] audit: type=2000 audit(1674288983.752:1): state=initialized audit_enabled=0 res=1 [ 3.025887] thermal_sys: Registered thermal governor 'step_wise' [ 3.025899] thermal_sys: Registered thermal governor 'user_space' [ 3.105784] EISA bus registered [ 3.225723] Searching for devices... [ 3.517647] Found devices: [ 3.553652] 1. Astro BC Runway Port [10] at 0xfffffffffed00000 { type:12, hv:0x582, sv:0xb, rev:0x0 } [ 3.673651] 2. Elroy PCI Bridge [10:0] at 0xfffffffffed30000 { type:13, hv:0x782, sv:0xa, rev:0x0 } [ 3.793651] 3. Elroy PCI Bridge [10:2] at 0xfffffffffed34000 { type:13, hv:0x782, sv:0xa, rev:0x0 } [ 3.913661] 4. Elroy PCI Bridge [10:4] at 0xfffffffffed38000 { type:13, hv:0x782, sv:0xa, rev:0x0 } [ 4.033655] 5. Elroy PCI Bridge [10:6] at 0xfffffffffed3c000 { type:13, hv:0x782, sv:0xa, rev:0x0 } [ 4.149651] 6. Duet W2 [32] at 0xfffffffffffa0000 { type:0, hv:0x5dd, sv:0x4, rev:0x0 } [ 4.257651] 7. Duet W2 [34] at 0xfffffffffffa2000 { type:0, hv:0x5dd, sv:0x4, rev:0x0 } [ 4.361651] 8. Memory [49] at 0xfffffffffed10200 { type:1, hv:0xa, sv:0x9, rev:0x0 } [ 4.461664] Enabling regular chassis codes support v0.05 [ 4.666247] CPU0: cpu core 0 of socket 0 [ 4.717860] CPU1: cpu core 0 of socket 1 [ 4.771154] Releasing cpu 1 now, hpa=fffffffffffa2000 [ 4.856528] CPU(s): 2 out of 2 PA8700 (PCX-W2) at 750.000000 MHz online [ 4.945926] alternatives: applied 65 out of 3100 patches [ 5.026153] Calculated flush threshold is 663 KiB [ 5.085709] Cache flush threshold set to 3072 KiB [ 5.149730] TLB flush threshold set to 480 KiB [ 5.234201] SBA found Astro 2.1 at 0xfffffffffed00000 [ 5.309357] Elroy version TR4.0 (0x5) found at 0xfffffffffed30000 [ 5.386921] LBA 10:0: PCI host bridge to bus 0000:00 [ 5.453798] pci_bus 0000:00: root bus resource [io 0x0000-0x1fff] [ 5.537687] pci_bus 0000:00: root bus resource [mem 0xfffffffff4000000-0xfffffffff47fffff] (bus address [0xf4000000-0xf47fffff]) [ 5.689953] pci 0000:00:0c.0: [1011:0019] type 00 class 0x020000 [ 5.765842] pci 0000:00:0c.0: reg 0x10: [io 0x1000-0x107f] [ 5.841793] pci 0000:00:0c.0: reg 0x14: [mem 0xfffffffff4008000-0xfffffffff40083ff] [ 5.942093] pci 0000:00:0c.0: reg 0x30: [mem 0xfffffffff4040000-0xfffffffff407ffff pref] [ 6.050437] pci 0000:00:0d.0: [11d4:1889] type 00 class 0x040100 [ 6.129834] pci 0000:00:0d.0: reg 0x10: [mem 0xfffffffff400c000-0xfffffffff400c1ff pref] [ 6.233748] pci 0000:00:0d.0: reg 0x14: [mem 0xfffffffff400b000-0xfffffffff400b00f pref] [ 6.341747] pci 0000:00:0d.0: reg 0x18: [mem 0xfffffffff400a000-0xfffffffff400a00f pref] [ 6.449747] pci 0000:00:0d.0: reg 0x1c: [mem 0xfffffffff4009000-0xfffffffff400900f pref] [ 6.554230] pci 0000:00:0d.0: supports D2 [ 6.610082] PCI: Enabled native mode for NS87415 (pif=0x8f) [ 6.681664] pci 0000:00:0e.0: superio_fixup_pci+0x0/0xf8 took 70312 usecs [ 6.769665] pci 0000:00:0e.0: [100b:0002] type 00 class 0x01018f [ 6.849835] pci 0000:00:0e.0: reg 0x10: [io 0x0f00-0x0f07] [ 6.925751] pci 0000:00:0e.0: reg 0x14: [io 0x0e00-0x0e03] [ 6.997751] pci 0000:00:0e.0: reg 0x18: [io 0x0d00-0x0d07] [ 7.069751] pci 0000:00:0e.0: reg 0x1c: [io 0x0b00-0x0b03] [ 7.145751] pci 0000:00:0e.0: reg 0x20: [io 0x0a00-0x0a0f] [ 7.218340] pci 0000:00:0e.1: [100b:000e] type 00 class 0x068000 [ 7.298792] pci 0000:00:0e.2: [100b:0012] type 00 class 0x0c0310 [ 7.377829] pci 0000:00:0e.2: reg 0x10: [mem 0xfffffffff4007000-0xfffffffff4007fff] [ 7.477748] pci 0000:00:0e.2: reg 0x14: [mem 0xfffffffff4006000-0xfffffffff4006fff] [ 7.582122] pci 0000:00:0f.0: [1000:000b] type 00 class 0x010000 [ 7.657825] pci 0000:00:0f.0: reg 0x10: [io 0x0900-0x09ff] [ 7.733796] pci 0000:00:0f.0: reg 0x14: [mem 0xfffffffff4005000-0xfffffffff40053ff 64bit] [ 7.841795] pci 0000:00:0f.0: reg 0x1c: [mem 0xfffffffff4002000-0xfffffffff4003fff 64bit] [ 7.950147] pci 0000:00:0f.0: supports D1 D2 [ 8.006237] pci 0000:00:0f.1: [1000:000b] type 00 class 0x010000 [ 8.085837] pci 0000:00:0f.1: reg 0x10: [io 0x0800-0x08ff] [ 8.157798] pci 0000:00:0f.1: reg 0x14: [mem 0xfffffffff4004000-0xfffffffff40043ff 64bit] [ 8.265798] pci 0000:00:0f.1: reg 0x1c: [mem 0xfffffffff4000000-0xfffffffff4001fff 64bit] [ 8.374147] pci 0000:00:0f.1: supports D1 D2 [ 8.431023] Elroy version TR4.0 (0x5) found at 0xfffffffffed34000 [ 8.514474] LBA 10:2: PCI host bridge to bus 0000:01 [ 8.577758] pci_bus 0000:01: root bus resource [io 0x14000-0x15fff] (bus address [0x4000-0x5fff]) [ 8.697667] pci_bus 0000:01: root bus resource [mem 0xfffffffff5000000-0xfffffffff57fffff] (bus address [0xf5000000-0xf57fffff]) [ 8.849839] pci_bus 0000:01: root bus resource [bus 01] [ 8.917900] pci 0000:01:01.0: [14e4:1645] type 00 class 0x020000 [ 8.997875] pci 0000:01:01.0: reg 0x10: [mem 0xfffffffff5000000-0xfffffffff500ffff 64bit] [ 9.106570] pci 0000:01:01.0: PME# supported from D3hot D3cold [ 9.183036] Elroy version TR4.0 (0x5) found at 0xfffffffffed38000 [ 9.266305] LBA 10:4: PCI host bridge to bus 0000:02 [ 9.329673] pci_bus 0000:02: root bus resource [io 0x28000-0x29fff] (bus address [0x8000-0x9fff]) [ 9.445667] pci_bus 0000:02: root bus resource [mem 0xfffffffffa000000-0xfffffffffbffffff] (bus address [0xfa000000-0xfbffffff]) [ 9.601667] pci_bus 0000:02: root bus resource [mem 0xfffffffff6000000-0xfffffffff67fffff] (bus address [0xf6000000-0xf67fffff]) [ 9.753667] pci_bus 0000:02: root bus resource [bus 02] [ 9.821802] pci 0000:02:02.0: [103c:1008] type 00 class 0x038000 [ 9.901892] pci 0000:02:02.0: reg 0x10: [mem 0xfffffffffa000000-0xfffffffffbffffff 64bit] [ 10.010058] pci 0000:02:02.0: reg 0x30: [mem 0xfffffffff6000000-0xfffffffff61fffff pref] [ 10.114548] iosapic: hpa not registered for 0000:02:02.0 [ 10.186150] Elroy version TR4.0 (0x5) found at 0xfffffffffed3c000 [ 10.266091] LBA 10:6: PCI host bridge to bus 0000:03 [ 10.333675] pci_bus 0000:03: root bus resource [io 0x3c000-0x3dfff] (bus address [0xc000-0xdfff]) [ 10.449666] pci_bus 0000:03: root bus resource [mem 0xfffffffff7000000-0xfffffffff77fffff] (bus address [0xf7000000-0xf77fffff]) [ 10.601668] pci_bus 0000:03: root bus resource [bus 03] [ 10.681648] powersw: Soft power switch at 0xfffffff0f0400804 enabled. [ 10.776652] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 10.865674] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 10.951085] iommu: Default domain type: Translated [ 11.013661] iommu: DMA domain TLB invalidation policy: strict mode [ 11.099655] NetLabel: Initializing [ 11.141659] NetLabel: domain hash size = 128 [ 11.201660] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 11.273781] NetLabel: unlabeled traffic allowed by default [ 11.349856] vgaarb: loaded [ 11.386963] VFS: Disk quotas dquot_6.6.0 [ 11.437790] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 11.530727] AppArmor: AppArmor Filesystem Enabled [ 11.602358] NET: Registered PF_INET protocol family [ 11.668042] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 11.783092] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 11.894391] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 11.999101] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 12.109110] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) [ 12.211598] TCP: Hash tables configured (established 65536 bind 65536) [ 12.298925] MPTCP token hash table entries: 8192 (order: 5, 196608 bytes, linear) [ 12.398171] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 12.486239] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 12.582285] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 12.657710] NET: Registered PF_XDP protocol family [ 12.717672] PCI: CLS 16 bytes [ 12.757735] SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 68) [ 12.853707] SuperIO: Serial port 1 at 0x3f8 [ 12.905669] SuperIO: Serial port 2 at 0x2f8 [ 12.961679] SuperIO: Parallel port at 0x378 [ 13.017667] SuperIO: Floppy controller at 0x3f0 [ 13.077679] SuperIO: ACPI at 0x7e0 [ 13.121848] SuperIO: USB regulator enabled [ 13.173719] pci 0000:00:0e.1: superio_init+0x0/0x798 took 406250 usecs [ 13.266268] clocksource: cr16_unstable: mask: 0xffffffffffffffff max_cycles: 0xacf9151134, max_idle_ns: 440795214493 ns [ 13.266658] Trying to unpack rootfs image as initramfs... [ 13.482447] Enabling PDC chassis warnings support v0.05 [ 13.550783] Performance monitoring counters enabled for Duet W2 [32] [ 13.634702] Initialise system trusted keyrings [ 13.693834] Key type blacklist registered [ 13.746164] workingset: timestamp_bits=46 max_order=21 bucket_order=0 [ 13.849254] zbud: loaded [ 13.889880] integrity: Platform Keyring initialized [ 13.953713] Key type asymmetric registered [ 14.005656] Asymmetric key parser 'x509' registered [ 18.140799] Freeing initrd memory: 28920K [ 18.195016] process '/usr/bin/kmod' started with executable stack [ 18.336754] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 18.410287] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 18.509920] io scheduler mq-deadline registered [ 18.573770] PDC Stable Storage facility v0.30 [ 18.957734] sticore: STI GSC/PCI core graphics driver Version 0.9c [ 19.037805] sticore: STI PCI graphic ROM found at fffffffff6000000 (2048 kB), fb at fffffffffa000000 (32 MB) [ 19.233922] sticore: STI word mode ROM supports 32 and 64 bit firmware functions. [ 19.329671] sticore: id 35acda30-9a02587, conforms to spec rev. 8.0d [ 19.417662] sticore: built-in font #1: size 10x20, chars 0-255, bpc 40 [ 19.505661] sticore: built-in font #2: size 8x16, chars 0-255, bpc 16 [ 19.597675] sticore: using 8x16 framebuffer font VGA8x16 [ 19.794160] sticore: graphics card name: A1262A [ 19.857679] sticore: located at [10/4/2/0] [ 19.917751] sticon: Initializing STI text console on A1262A at [10/4/2/0] [ 20.200033] Console: switching consoles 1-63 to colour STI console 200x75 [ 20.473714] stifb: 'A1262A' (id: 0x35acda30) not supported. [ 20.549960] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 20.629871] serial8250: ttyS0 at I/O 0x3f8 (irq = 3, base_baud = 115200) is a 16550A [ 20.733732] printk: console [ttyS0] enabled [ 20.733732] printk: console [ttyS0] enabled [ 20.837668] printk: bootconsole [pdc0] disabled [ 20.837668] printk: bootconsole [pdc0] disabled [ 20.954020] serial8250: ttyS1 at I/O 0x2f8 (irq = 4, base_baud = 115200) is a 16550A [ 21.046839] Linux agpgart interface v0.103 [ 21.093656] quicksilver: No Pluto found, so no AGPGART for you. [ 21.166413] mousedev: PS/2 mouse device common for all mice [ 21.235597] rtc-generic rtc-generic: registered as rtc0 [ 21.301672] rtc-generic rtc-generic: setting system clock to 2023-01-21T08:16:42 UTC (1674289002) [ 21.405801] ledtrig-cpu: registered to indicate activity on CPUs [ 21.479077] NET: Registered PF_INET6 protocol family [ 21.607299] Segment Routing with IPv6 [ 21.649921] In-situ OAM (IOAM) with IPv6 [ 21.697874] mip6: Mobile IPv6 [ 21.733693] NET: Registered PF_PACKET protocol family [ 21.793864] mpls_gso: MPLS GSO support [ 21.838984] registered taskstats version 1 [ 21.889698] Loading compiled-in X.509 certificates [ 21.968610] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 22.069893] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 22.198346] zswap: loaded using pool lzo/zbud [ 22.251333] Key type .fscrypt registered [ 22.297735] Key type fscrypt-provisioning registered [ 22.420158] Key type encrypted registered [ 22.465706] AppArmor: AppArmor sha1 policy hashing enabled [ 22.533815] ima: No TPM chip found, activating TPM-bypass! [ 22.597749] ima: Allocated hash algorithm: sha256 [ 22.653742] ima: No architecture policies found [ 22.709868] evm: Initialising EVM extended attributes: [ 22.769753] evm: security.selinux [ 22.809651] evm: security.SMACK64 (disabled) [ 22.861683] evm: security.SMACK64EXEC (disabled) [ 22.917663] evm: security.SMACK64TRANSMUTE (disabled) [ 22.977661] evm: security.SMACK64MMAP (disabled) [ 23.033654] evm: security.apparmor [ 23.073661] evm: security.ima [ 23.109652] evm: security.capability [ 23.153664] evm: HMAC attrs: 0x1 [ 23.195237] Unstable clock detected, switching default tracing clock to "global" [ 23.195237] If you want to keep using the local clock, then add: [ 23.195237] "trace_clock=local" [ 23.195237] on the kernel command line [ 24.889177] Freeing unused kernel image (initmem) memory: 2048K [ 24.957710] Write protected read-only-after-init data: 128k [ 25.025701] Run /init as init process Loading, please wait... Starting systemd-udevd version 252.4-1 [ 25.956105] tulip alternatives: applied 0 out of 1 patches [ 26.077391] usbcore alternatives: applied 0 out of 20 patches [ 26.161091] pps_core: LinuxPPS API ver. 1 registered [ 26.166427] tulip0: no phy info, aborting mtable build [ 26.217831] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 26.282445] tulip0: MII transceiver #1 config 1000 status 782d advertising 01e1 [ 26.489946] scsi_mod alternatives: applied 0 out of 7 patches [ 26.590152] usbcore: registered new interface driver usbfs [ 26.664593] SCSI subsystem initialized [ 26.665613] usbcore: registered new interface driver hub [ 26.789969] PTP clock support registered [ 26.857161] sym53c8xx alternatives: applied 0 out of 26 patches [ 26.951153] usbcore: registered new device driver usb [ 27.013746] libata alternatives: applied 0 out of 3 patches [ 27.111017] ehci_hcd alternatives: applied 0 out of 131 patches [ 27.182139] tg3 alternatives: applied 0 out of 88 patches [ 27.254255] net eth0: Digital DS21142/43 Tulip rev 65 at MMIO 0xfffffffff4008000, 00:30:6e:21:bc:37, IRQ 66 [ 27.313658] sym0: <896> rev 0x7 at pci 0000:00:0f.0 irq 69 [ 27.444757] sym0: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking [ 27.444797] ohci_hcd alternatives: applied 0 out of 138 patches [ 27.525637] sym0: SCSI BUS has been reset. [ 27.642155] scsi host0: sym-2.2.3 [ 27.916084] sym1: <896> rev 0x7 at pci 0000:00:0f.1 irq 69 [ 27.984857] sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking [ 28.069637] sym1: SCSI BUS has been reset. [ 28.117708] scsi host1: sym-2.2.3 [ 28.956120] tg3 0000:01:01.0 eth1: Tigon3 [partno(A6825-60101) rev 0105] (PCI:66MHz:64-bit) MAC address 00:13:21:ea:37:16 [ 29.088716] tg3 0000:01:01.0 eth1: attached PHY is 5701 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0]) [ 29.201704] tg3 0000:01:01.0 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[0] [ 29.297664] tg3 0000:01:01.0 eth1: dma_rwctrl[76ff2d0f] dma_mask[64-bit] [ 32.608957] scsi 1:0:5:0: Direct-Access COMPAQ BD30088279 HPB4 PQ: 0 ANSI: 3 [ 32.705732] scsi target1:0:5: tagged command queuing enabled, command queue depth 16. [ 32.809681] scsi target1:0:5: Beginning Domain Validation [ 32.881230] scsi target1:0:5: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31) [ 32.972646] scsi target1:0:5: Domain Validation skipping write tests [ 33.045671] scsi target1:0:5: Ending Domain Validation [ 33.111943] scsi 1:0:6:0: Direct-Access COMPAQ BD30089BBA HPB1 PQ: 0 ANSI: 3 [ 33.205667] scsi target1:0:6: tagged command queuing enabled, command queue depth 16. [ 33.317674] scsi target1:0:6: Beginning Domain Validation [ 33.391283] scsi target1:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31) [ 33.483820] scsi target1:0:6: Domain Validation skipping write tests [ 33.557661] scsi target1:0:6: Ending Domain Validation [ 36.017695] pata_ns87415 alternatives: applied 0 out of 1 patches [ 36.027012] tulip 0000:00:0c.0 enp0s12: renamed from eth0 [ 36.162292] ehci_pci alternatives: applied 0 out of 2 patches [ 36.163714] scsi host2: pata_ns87415 [ 36.311568] scsi host3: pata_ns87415 [ 36.363922] ohci-pci 0000:00:0e.2: OHCI PCI host controller [ 36.438540] ata1: PATA max MWDMA2 cmd 0xf00 ctl 0xe00 bmdma 0xa00 irq 7 [ 36.438834] tg3 0000:01:01.0 enp1s1: renamed from eth1 [ 36.517809] ata2: PATA max MWDMA2 cmd 0xd00 ctl 0xb00 bmdma 0xa08 irq 7 [ 36.660352] ohci-pci 0000:00:0e.2: new USB bus registered, assigned bus number 1 [ 36.751623] ohci-pci 0000:00:0e.2: irq 1, io mem 0xfffffffff4007000 [ 36.842342] ata1.00: ATAPI: CD-224E, 1.7A, max UDMA/33 [ 36.906109] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 37.001736] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 37.090155] usb usb1: Product: OHCI PCI host controller [ 37.153947] usb usb1: Manufacturer: Linux 6.1.0-1-parisc64 ohci_hcd [ 37.229667] usb usb1: SerialNumber: 0000:00:0e.2 [ 37.301305] scsi 2:0:0:0: CD-ROM TEAC CD-224E 1.7A PQ: 0 ANSI: 5 [ 37.406213] hub 1-0:1.0: USB hub found [ 37.478184] hub 1-0:1.0: 3 ports detected [ 37.670856] sd 1:0:6:0: Power-on or device reset occurred [ 37.735531] sd 1:0:5:0: Power-on or device reset occurred [ 37.803509] sd 1:0:6:0: [sdb] 585937500 512-byte logical blocks: (300 GB/279 GiB) [ 37.895018] sd 1:0:5:0: [sda] 585937500 512-byte logical blocks: (300 GB/279 GiB) [ 37.987412] sd 1:0:5:0: [sda] Write Protect is off [ 38.045794] sd 1:0:6:0: [sdb] Write Protect is off [ 38.103147] sd 1:0:6:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA [ 38.205738] sd 1:0:5:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA [ 38.334418] sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 > [ 38.390176] sd 1:0:6:0: [sdb] Attached SCSI disk [ 38.458089] sda: sda1 sda2 sda3 < sda5 sda6 > [ 38.516261] sd 1:0:5:0: [sda] Attached SCSI disk [ 38.640341] sr 2:0:0:0: [sr0] scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray [ 38.725717] cdrom: Uniform CD-ROM driver Revision: 3.20 root@parisc:/# lspci 00:0c.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41) 00:0d.0 Multimedia audio controller: Analog Devices Device 1889 00:0e.0 IDE interface: National Semiconductor Corporation 87415/87560 IDE (rev 03) 00:0e.1 Bridge: National Semiconductor Corporation 87560 Legacy I/O (rev 01) 00:0e.2 USB controller: National Semiconductor Corporation USB Controller (rev 02) 00:0f.0 SCSI storage controller: Broadcom / LSI 53C896/897 (rev 07) 00:0f.1 SCSI storage controller: Broadcom / LSI 53C896/897 (rev 07) 01:01.0 Ethernet controller: Broadcom Inc. and subsidiaries NetXtreme BCM5701 Gigabit Ethernet (rev 15) 02:02.0 Display controller: Hewlett-Packard Company Visualize FX (rev 02)