Linux version 6.1.79+ (deller@p100) (hppa64-linux-gnu-gcc (GCC) 13.2.1 20230728 (Red Hat Cross 13.2.1-1), GNU ld version 2.40-3.fc39) #529 SMP Wed Feb 28 14:26:25 CET 2024 FP[0] enabled: Rev 1 Model 20 The 64-bit Kernel has started... Kernel default page size is 4 KB. Huge pages enabled with 1 MB physical and 2 MB virtual size. Determining PDC firmware type: 64 bit PAT. PAT: Running on cell 0 and location 1. PAT: legacy revision 0x24, pat_rev 0x201, pdc_cap 0x132, S-PTLB 0, HPMC_RENDEZ 0. model 00008950 00000491 00000000 00000002 3e14792c381d39d8 100000f0 00000008 000000b2 000000b2 vers 00000302 CPUID vers 20 rev 5 (0x00000285) capabilities 0x35 model 9000/800/rp3440 product A7137AR, original product A7137AR, S/N: DEH50118AM parisc_cache_init: Only equivalent aliasing supported! Memory Ranges: 0) Start 0x0000000000000000 End 0x000000003fffffff Size 1024 MB 1) Start 0x0000000100000000 End 0x00000001ffdfffff Size 4094 MB 2) Start 0x0000004040000000 End 0x00000040ffffffff Size 3072 MB Total Memory: 8190 MB initrd: 7e55c000-7ffee2a8 initrd: reserving 3e55c000-3ffee2a8 (mem_max 1ffe00000) PDT: type PDT_PAT_NEW, size 3000, entries 2, status 0, dbe_loc 0x407cd23500, good_mem 0 MB PDT: Firmware reports 2 entries of faulty memory: PDT: BAD MEMORY at 0x407cd23500, DIMM slot 4a, permanent multi-bit error. PDT: BAD MEMORY at 0x40f9a38100, DIMM slot 4a, permanent multi-bit error. Zone ranges: Normal [mem 0x0000000000000000-0x00040fffffffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x000000003fffffff] node 0: [mem 0x0000000100000000-0x00000001ffdfffff] node 0: [mem 0x0000004040000000-0x00000040ffffffff] Initmem setup node 0 [mem 0x0000000000000000-0x00000040ffffffff] On node 0, zone Normal: 512 pages in unavailable ranges percpu: Embedded 46 pages/cpu s149728 r8192 d30496 u188416 pcpu-alloc: s149728 r8192 d30496 u188416 alloc=46*4096 pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 SMP: bootstrap CPU ID is 0 Built 1 zonelists, mobility grouping on. Total pages: 2063880 Kernel command line: root=LABEL=ROOT300r HOME=/ cryptomgr.notests console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux earlycon=pdc earlycon: pdc0 at MMIO32be 0x0000000000000000 (options '') printk: bootconsole [pdc0] enabled Unknown kernel command line parameters "palo_kernel=2/vmlinux", will be passed to user space. Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) Sorting __ex_table... mem auto-init: stack:off, heap alloc:on, heap free:off Memory: 0K/8386560K available (15140K kernel code, 5819K rwdata, 2110K rodata, 2048K init, 836K bss, 215064K reserved, 0K cma-reserved) SLUB: HWalign=16, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 ftrace: allocating 29154 entries in 114 pages ftrace: allocated 114 pages with 4 groups trace event string verifier disabled rcu: Hierarchical RCU implementation. Rude variant of Tasks RCU enabled. Tracing variant of Tasks RCU enabled. rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. NR_IRQS: 128 rcu: srcu_init: Setting srcu_struct sizes based on contention. sched_clock: 64 bits at 800MHz, resolution 1ns, wraps every 4398046511103ns Console: colour dummy device 160x64 Calibrating delay loop... 1594.36 BogoMIPS (lpj=3188736) pid_max: default: 32768 minimum: 301 LSM: Security Framework initializing Yama: becoming mindful. AppArmor: AppArmor initialized TOMOYO Linux initialized Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) cblist_init_generic: Setting adjustable number of callback queues. cblist_init_generic: Setting shift to 3 and lim to 1. cblist_init_generic: Setting adjustable number of callback queues. cblist_init_generic: Setting shift to 3 and lim to 1. TOC handler registered rcu: Hierarchical SRCU implementation. rcu: Max phase no-delay instances is 1000. smp: Bringing up secondary CPUs ... smp: Brought up 1 node, 1 CPU node 0 deferred pages initialised in 576ms devtmpfs: initialized clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns futex hash table entries: 2048 (order: 4, 98304 bytes, linear) NET: Registered PF_NETLINK/PF_ROUTE protocol family audit: initializing netlink subsys (disabled) thermal_sys: Registered thermal governor 'fair_share' thermal_sys: Registered thermal governor 'bang_bang' thermal_sys: Registered thermal governor 'step_wise' audit: type=2000 audit(1709128683.728:1): state=initialized audit_enabled=0 res=1 thermal_sys: Registered thermal governor 'user_space' EISA bus registered Searching for devices... Found devices: 1. Storm Peak Slow Mako+ [128] at 0xfffffffffe780000 { type:0, hv:0x895, sv:0x4, rev:0x0 } 2. Storm Peak Slow Mako+ [129] at 0xfffffffffe781000 { type:0, hv:0x895, sv:0x4, rev:0x0 } 3. Storm Peak Slow Mako+ [152] at 0xfffffffffe798000 { type:0, hv:0x895, sv:0x4, rev:0x0 } 4. Storm Peak Slow Mako+ [153] at 0xfffffffffe799000 { type:0, hv:0x895, sv:0x4, rev:0x0 } 5. Everest Mako Memory [8] at 0xfffffffffed08000 { type:1, hv:0xaf, sv:0x9, rev:0x0 } 6. Pluto BC McKinley Port [0] at 0xfffffffffed00000 { type:12, hv:0x880, sv:0xc, rev:0x0 } 7. Mercury PCI Bridge [0:0] at 0xfffffffffed20000 { type:13, hv:0x783, sv:0xa, rev:0x0 } 8. Mercury PCI Bridge [0:1] at 0xfffffffffed22000 { type:13, hv:0x783, sv:0xa, rev:0x0 } 9. Mercury PCI Bridge [0:2] at 0xfffffffffed24000 { type:13, hv:0x783, sv:0xa, rev:0x0 } 10. Mercury PCI Bridge [0:3] at 0xfffffffffed26000 { type:13, hv:0x783, sv:0xa, rev:0x0 } 11. Mercury PCI Bridge [0:4] at 0xfffffffffed28000 { type:13, hv:0x783, sv:0xa, rev:0x0 } 12. Mercury PCI Bridge [0:6] at 0xfffffffffed2c000 { type:13, hv:0x783, sv:0xa, rev:0x0 } 13. Mercury PCI Bridge [0:7] at 0xfffffffffed2e000 { type:13, hv:0x783, sv:0xa, rev:0x0 } 14. BMC IPMI Mgmt Ctlr [16] at 0xfffffff0f05b0000 { type:15, hv:0x4, sv:0xc0, rev:0x0 } Enabling PDC_PAT chassis codes support v0.05 Logical CPU #0 is physical cpu #0 at location 0xffff0000ffff15 with hpa 0xfffffffffe780000 CPU0: cpu core 0 of socket 0 Logical CPU #1 is physical cpu #1 at location 0xffff0000ffff15 with hpa 0xfffffffffe781000 CPU1: cpu core 1 of socket 0 Releasing cpu 1 now, hpa=fffffffffe781000 Logical CPU #2 is physical cpu #2 at location 0xffff0001ffff15 with hpa 0xfffffffffe798000 CPU2: cpu core 0 of socket 1 Releasing cpu 2 now, hpa=fffffffffe798000 Logical CPU #3 is physical cpu #3 at location 0xffff0001ffff15 with hpa 0xfffffffffe799000 CPU3: cpu core 1 of socket 1 Releasing cpu 3 now, hpa=fffffffffe799000 CPU(s): 4 out of 4 PA8900 (Shortfin) at 799.997100 MHz online alternatives: applied 63 out of 3360 patches Whole cache flush 5326118 cycles, flushing 25165824 bytes 6029886 cycles Calculated flush threshold is 21707 KiB Cache flush threshold set to 262144 KiB Whole TLB flush 25588 cycles, Range flush 25165824 bytes 1860980 cycles Calculated TLB flush threshold 1352 KiB TLB flush threshold set to 1352 KiB SBA found Pluto 2.3 at 0xfffffffffed00000 Mercury version TR3.2 (0x32) found at 0xfffffffffed20000 LBA 0:0: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x0000-0xffff] pci_bus 0000:00: root bus resource [mem 0xffffffff80000000-0xffffffff8fffffff] (bus address [0x80000000-0x8fffffff]) pci_bus 0000:00: root bus resource [bus 00-07] pci 0000:00:01.0: [1033:0035] type 00 class 0x0c0310 pci 0000:00:01.0: reg 0x10: [mem 0xffffffff80002000-0xffffffff80002fff] pci 0000:00:01.0: supports D1 D2 pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot pci 0000:00:01.1: [1033:0035] type 00 class 0x0c0310 pci 0000:00:01.1: reg 0x10: [mem 0xffffffff80001000-0xffffffff80001fff] pci 0000:00:01.1: supports D1 D2 pci 0000:00:01.1: PME# supported from D0 D1 D2 D3hot pci 0000:00:01.2: [1033:00e0] type 00 class 0x0c0320 pci 0000:00:01.2: reg 0x10: [mem 0xffffffff80000000-0xffffffff800000ff] pci 0000:00:01.2: supports D1 D2 pci 0000:00:01.2: PME# supported from D0 D1 D2 D3hot pci 0000:00:02.0: [1095:0649] type 00 class 0x01018f pci 0000:00:02.0: reg 0x10: [io 0x0d18-0x0d1f] pci 0000:00:02.0: reg 0x14: [io 0x0d24-0x0d27] pci 0000:00:02.0: reg 0x18: [io 0x0d10-0x0d17] pci 0000:00:02.0: reg 0x1c: [io 0x0d20-0x0d23] pci 0000:00:02.0: reg 0x20: [io 0x0d00-0x0d0f] pci 0000:00:02.0: supports D1 D2 Mercury version TR3.2 (0x32) found at 0xfffffffffed22000 LBA 0:1: PCI host bridge to bus 0000:20 pci_bus 0000:20: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) pci_bus 0000:20: root bus resource [mem 0xffffffff90000000-0xffffffff9fffffff] (bus address [0x90000000-0x9fffffff]) pci_bus 0000:20: root bus resource [bus 20-27] pci 0000:20:01.0: [1000:0021] type 00 class 0x010000 pci 0000:20:01.0: reg 0x10: [io 0x12100-0x121ff] pci 0000:20:01.0: reg 0x14: [mem 0xffffffff90015000-0xffffffff900153ff 64bit] pci 0000:20:01.0: reg 0x1c: [mem 0xffffffff90012000-0xffffffff90013fff 64bit] pci 0000:20:01.0: supports D1 D2 pci 0000:20:01.1: [1000:0021] type 00 class 0x010000 pci 0000:20:01.1: reg 0x10: [io 0x12000-0x120ff] pci 0000:20:01.1: reg 0x14: [mem 0xffffffff90014000-0xffffffff900143ff 64bit] pci 0000:20:01.1: reg 0x1c: [mem 0xffffffff90010000-0xffffffff90011fff 64bit] pci 0000:20:01.1: supports D1 D2 pci 0000:20:02.0: [14e4:1645] type 00 class 0x020000 pci 0000:20:02.0: reg 0x10: [mem 0xffffffff90000000-0xffffffff9000ffff 64bit] pci 0000:20:02.0: PME# supported from D3hot D3cold Mercury version TR3.2 (0x32) found at 0xfffffffffed24000 LBA 0:2: PCI host bridge to bus 0000:40 pci_bus 0000:40: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff]) pci_bus 0000:40: root bus resource [mem 0xffffffffa0000000-0xffffffffafffffff] (bus address [0xa0000000-0xafffffff]) pci_bus 0000:40: root bus resource [bus 40-47] Mercury version TR3.2 (0x32) found at 0xfffffffffed26000 LBA 0:3: PCI host bridge to bus 0000:60 pci_bus 0000:60: root bus resource [io 0x30000-0x3ffff] (bus address [0x0000-0xffff]) pci_bus 0000:60: root bus resource [mem 0xffffffffb0000000-0xffffffffbfffffff] (bus address [0xb0000000-0xbfffffff]) pci_bus 0000:60: root bus resource [bus 60-67] pci 0000:60:01.0: [14e4:1645] type 00 class 0x020000 pci 0000:60:01.0: reg 0x10: [mem 0xffffffffb0000000-0xffffffffb000ffff 64bit] pci 0000:60:01.0: PME# supported from D3hot Mercury version TR3.2 (0x32) found at 0xfffffffffed28000 LBA: lmmio_space [0xffffffffc0000000-0xffffffffdfffffff] - new LBA 0:4: PCI host bridge to bus 0000:80 pci_bus 0000:80: root bus resource [io 0x40000-0x4ffff] (bus address [0x0000-0xffff]) pci_bus 0000:80: root bus resource [mem 0xffffffffc0000000-0xffffffffdfffffff] (bus address [0xc0000000-0xdfffffff]) pci_bus 0000:80: root bus resource [bus 80-87] Mercury version TR3.2 (0x32) found at 0xfffffffffed2c000 LBA 0:6: PCI host bridge to bus 0000:c0 pci_bus 0000:c0: root bus resource [io 0x50000-0x5ffff] (bus address [0x0000-0xffff]) pci_bus 0000:c0: root bus resource [mem 0xffffffffe0000000-0xffffffffefffffff] (bus address [0xe0000000-0xefffffff]) pci_bus 0000:c0: root bus resource [bus c0-c7] Mercury version TR3.2 (0x32) found at 0xfffffffffed2e000 LBA: lmmio_space [0xfffffffff0000000-0xfffffffffe77ffff] - new LBA 0:7: PCI host bridge to bus 0000:e0 pci_bus 0000:e0: root bus resource [io 0x60000-0x6ffff] (bus address [0x0000-0xffff]) pci_bus 0000:e0: root bus resource [mem 0xfffffffff0000000-0xfffffffffe77ffff] (bus address [0xf0000000-0xfe77ffff]) pci_bus 0000:e0: root bus resource [bus e0-e7] pci 0000:e0:01.0: [103c:1290] type 00 class 0x078000 pci 0000:e0:01.0: reg 0x18: [mem 0xfffffffff4051000-0xfffffffff405100f] pci 0000:e0:01.0: Hiding Diva built-in AUX serial device pci 0000:e0:01.1: [103c:1048] type 00 class 0x070002 pci 0000:e0:01.1: reg 0x10: [mem 0xfffffffff4050000-0xfffffffff4050fff] pci 0000:e0:01.1: reg 0x18: [mem 0xfffffffff4020000-0xfffffffff403ffff pref] pci 0000:e0:02.0: [1002:5159] type 00 class 0x030000 pci 0000:e0:02.0: reg 0x10: [mem 0xfffffffff0000000-0xfffffffff3ffffff pref] pci 0000:e0:02.0: reg 0x14: [io 0x6e000-0x6e0ff] pci 0000:e0:02.0: reg 0x18: [mem 0xfffffffff4040000-0xfffffffff404ffff] pci 0000:e0:02.0: reg 0x30: [mem 0xfffffffff4000000-0xfffffffff401ffff pref] pci 0000:e0:02.0: Hiding Diva built-in ATI card pci 0000:e0:02.0: supports D1 D2 powersw: Soft power switch support not available. HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page iommu: Default domain type: Translated iommu: DMA domain TLB invalidation policy: strict mode NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO NetLabel: unlabeled traffic allowed by default pci 0000:e0:02.0: vgaarb: setting as boot VGA device pci 0000:e0:02.0: vgaarb: bridge control possible pci 0000:e0:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none vgaarb: loaded VFS: Disk quotas dquot_6.6.0 VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) AppArmor: AppArmor Filesystem Enabled NET: Registered PF_INET protocol family IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 98304 bytes, linear) Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) TCP bind hash table entries: 65536 (order: 9, 3145728 bytes, linear) TCP: Hash tables configured (established 65536 bind 65536) MPTCP token hash table entries: 8192 (order: 6, 327680 bytes, linear) UDP hash table entries: 4096 (order: 6, 262144 bytes, linear) UDP-Lite hash table entries: 4096 (order: 6, 262144 bytes, linear) NET: Registered PF_UNIX/PF_LOCAL protocol family NET: Registered PF_XDP protocol family PCI: CLS 16 bytes pci 0000:00:01.0: quirk_usb_early_handoff+0x0/0xc90 took 78125 usecs pci 0000:00:01.1: quirk_usb_early_handoff+0x0/0xc90 took 74218 usecs pci 0000:00:01.2: quirk_usb_early_handoff+0x0/0xc90 took 78125 usecs clocksource: cr16_unstable: mask: 0xffffffffffffffff max_cycles: 0xb880fbadad, max_idle_ns: 440795225955 ns Trying to unpack rootfs image as initramfs... Chassis warnings not supported. Performance monitoring counters enabled for Storm Peak Slow Mako+ [128] Initialise system trusted keyrings Key type blacklist registered workingset: timestamp_bits=46 max_order=21 bucket_order=0 zbud: loaded integrity: Platform Keyring initialized Key type asymmetric registered Asymmetric key parser 'x509' registered Freeing initrd memory: 27208K process '/usr/bin/kmod' started with executable stack alg: self-tests for CTR-KDF (hmac(sha256)) passed Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) io scheduler mq-deadline registered PDC Stable Storage facility v0.30 sticore: STI GSC/PCI core graphics driver Version 0.9c Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled printk: console [ttyS0] disabled 0000:e0:01.1: ttyS0 at MMIO 0xfffffffff4050000 (irq = 74, base_baud = 115200) is a 16550A printk: console [ttyS0] enabled printk: bootconsole [pdc0] disabled 0000:e0:01.1: ttyS1 at MMIO 0xfffffffff4050010 (irq = 74, base_baud = 115200) is a 16550A 0000:e0:01.1: ttyS2 at MMIO 0xfffffffff4050038 (irq = 74, base_baud = 115200) is a 16550A Linux agpgart interface v0.103 quicksilver: No AGP devices found. mousedev: PS/2 mouse device common for all mice rtc-generic rtc-generic: registered as rtc0 rtc-generic rtc-generic: setting system clock to 2024-02-28T13:58:11 UTC (1709128691) ledtrig-cpu: registered to indicate activity on CPUs NET: Registered PF_INET6 protocol family Segment Routing with IPv6 In-situ OAM (IOAM) with IPv6 mip6: Mobile IPv6 NET: Registered PF_PACKET protocol family mpls_gso: MPLS GSO support registered taskstats version 1 Loading compiled-in X.509 certificates zswap: loaded using pool lzo/zbud Key type .fscrypt registered Key type fscrypt-provisioning registered Key type encrypted registered AppArmor: AppArmor sha1 policy hashing enabled ima: No TPM chip found, activating TPM-bypass! ima: Allocated hash algorithm: sha256 ima: No architecture policies found evm: Initialising EVM extended attributes: evm: security.selinux evm: security.SMACK64 (disabled) evm: security.SMACK64EXEC (disabled) evm: security.SMACK64TRANSMUTE (disabled) evm: security.SMACK64MMAP (disabled) evm: security.apparmor evm: security.ima evm: security.capability evm: HMAC attrs: 0x1 Unstable clock detected, switching default tracing clock to "global" If you want to keep using the local clock, then add: "trace_clock=local" on the kernel command line Freeing unused kernel image (initmem) memory: 2048K Write protected read-only-after-init data: 125k Run /init as init process with arguments: /init with environment: HOME=/ TERM=vt102 palo_kernel=2/vmlinux scsi_mod alternatives: applied 0 out of 7 patches SCSI subsystem initialized pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered usbcore alternatives: applied 0 out of 20 patches usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ehci_hcd alternatives: applied 0 out of 131 patches libata alternatives: applied 0 out of 3 patches sym53c8xx alternatives: applied 0 out of 26 patches libata version 3.00 loaded. ehci_pci alternatives: applied 0 out of 2 patches ehci-pci 0000:00:01.2: EHCI Host Controller ehci-pci 0000:00:01.2: new USB bus registered, assigned bus number 1 ohci_hcd alternatives: applied 0 out of 138 patches ehci-pci 0000:00:01.2: irq 68, io mem 0xffffffff80000000 ehci-pci 0000:00:01.2: USB 2.0 started, EHCI 0.95 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 6.1.79+ ehci_hcd usb usb1: SerialNumber: 0000:00:01.2 pata_cmd64x 0000:00:02.0: Secondary port is disabled hub 1-0:1.0: USB hub found hub 1-0:1.0: 5 ports detected scsi host0: pata_cmd64x scsi host1: pata_cmd64x ata1: PATA max UDMA/100 cmd 0xd18 ctl 0xd24 bmdma 0xd00 irq 69 ata2: DUMMY ata1.00: ATAPI: DVD-ROM DW-224EV, K.DA, max UDMA/33 scsi 0:0:0:0: CD-ROM TEAC DVD-ROM DW-224EV K.DA PQ: 0 ANSI: 5 tg3 alternatives: applied 0 out of 88 patches ohci-pci 0000:00:01.0: OHCI PCI host controller ohci-pci 0000:00:01.0: new USB bus registered, assigned bus number 2 ohci-pci 0000:00:01.0: irq 66, io mem 0xffffffff80002000 sym0: <1010-66> rev 0x1 at pci 0000:20:01.0 irq 70 sym0: PA-RISC Firmware, ID 7, Fast-80, LVD, parity checking sym0: SCSI BUS has been reset. scsi host2: sym-2.2.3 sym1: <1010-66> rev 0x1 at pci 0000:20:01.1 irq 71 sym1: PA-RISC Firmware, ID 7, Fast-80, LVD, parity checking sym1: SCSI BUS has been reset. scsi host3: sym-2.2.3 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OHCI PCI host controller usb usb2: Manufacturer: Linux 6.1.79+ ohci_hcd usb usb2: SerialNumber: 0000:00:01.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected ohci-pci 0000:00:01.1: OHCI PCI host controller ohci-pci 0000:00:01.1: new USB bus registered, assigned bus number 3 ohci-pci 0000:00:01.1: irq 67, io mem 0xffffffff80001000 usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: OHCI PCI host controller usb usb3: Manufacturer: Linux 6.1.79+ ohci_hcd usb usb3: SerialNumber: 0000:00:01.1 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected tg3 0000:20:02.0 eth0: Tigon3 [partno(BCM95700A6) rev 0105] (PCI:66MHz:64-bit) MAC address 00:16:35:73:70:73 tg3 0000:20:02.0 eth0: attached PHY is 5701 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0]) tg3 0000:20:02.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[0] tg3 0000:20:02.0 eth0: dma_rwctrl[76ff2d0f] dma_mask[64-bit] tg3 0000:60:01.0 eth1: Tigon3 [partno(A6825-60101) rev 0105] (PCI:66MHz:64-bit) MAC address 00:30:6e:f4:47:8c tg3 0000:60:01.0 eth1: attached PHY is 5701 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0]) tg3 0000:60:01.0 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[0] tg3 0000:60:01.0 eth1: dma_rwctrl[76ff2d0f] dma_mask[64-bit] scsi 2:0:0:0: Direct-Access COMPAQ BD30089BBA HPB1 PQ: 0 ANSI: 3 scsi target2:0:0: tagged command queuing enabled, command queue depth 16. scsi target2:0:0: Beginning Domain Validation scsi target2:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31) scsi 2:0:0:0: Power-on or device reset occurred scsi target2:0:0: Ending Domain Validation scsi 3:0:2:0: Direct-Access COMPAQ BF07288285 HPB3 PQ: 0 ANSI: 3 scsi target3:0:2: tagged command queuing enabled, command queue depth 16. scsi target3:0:2: Beginning Domain Validation scsi target3:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31) scsi 3:0:2:0: Power-on or device reset occurred scsi target3:0:2: Ending Domain Validation tg3 0000:20:02.0 enp32s2: renamed from eth0 tg3 0000:60:01.0 enp96s1: renamed from eth1 sr 0:0:0:0: [sr0] scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray cdrom: Uniform CD-ROM driver Revision: 3.20 sr 0:0:0:0: Attached scsi CD-ROM sr0 sd 2:0:0:0: [sda] 585937500 512-byte logical blocks: (300 GB/279 GiB) sd 3:0:2:0: [sdb] 142264000 512-byte logical blocks: (72.8 GB/67.8 GiB) sd 3:0:2:0: [sdb] Write Protect is off sd 3:0:2:0: [sdb] Mode Sense: d3 00 10 08 sd 2:0:0:0: [sda] Write Protect is off sd 3:0:2:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 2:0:0:0: [sda] Mode Sense: cf 00 10 08 sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA random: crng init done sdb: sdb1 sda: sda1 sda2 sda3 sd 3:0:2:0: [sdb] Attached SCSI disk sd 2:0:0:0: [sda] Attached SCSI disk EXT4-fs (sda3): mounted filesystem with ordered data mode. Quota mode: none. Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. systemd[1]: Inserted module 'autofs4' x_tables alternatives: applied 0 out of 4 patches ip_tables alternatives: applied 0 out of 6 patches systemd[1]: systemd 255.3-2 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK -SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) systemd[1]: Detected architecture parisc64. systemd[1]: Hostname set to . processor : 0 cpu family : PA-RISC 2.0 cpu : PA8900 (Shortfin) cpu MHz : 799.997100 physical id : 0 siblings : 2 core id : 0 capabilities : os64 iopdir_fdc needs_equivalent_aliasing (0x35) model : 9000/800/rp3440 - Storm Peak Slow Mako+ hversion : 0x00008950 sversion : 0x00000491 I-cache : 65536 KB D-cache : 65536 KB (WB, direct mapped, alias=0) ITLB entries : 240 DTLB entries : 240 - shared with ITLB bogomips : 1594.36 software id : 4473333560712706520 processor : 1 cpu family : PA-RISC 2.0 cpu : PA8900 (Shortfin) cpu MHz : 799.997100 physical id : 0 siblings : 2 core id : 1 capabilities : os64 iopdir_fdc needs_equivalent_aliasing (0x35) model : 9000/800/rp3440 - Storm Peak Slow Mako+ hversion : 0x00008950 sversion : 0x00000491 I-cache : 65536 KB D-cache : 65536 KB (WB, direct mapped, alias=0) ITLB entries : 240 DTLB entries : 240 - shared with ITLB bogomips : 1594.36 software id : 4473333560712706520 processor : 2 cpu family : PA-RISC 2.0 cpu : PA8900 (Shortfin) cpu MHz : 799.997100 physical id : 1 siblings : 2 core id : 0 capabilities : os64 iopdir_fdc needs_equivalent_aliasing (0x35) model : 9000/800/rp3440 - Storm Peak Slow Mako+ hversion : 0x00008950 sversion : 0x00000491 I-cache : 65536 KB D-cache : 65536 KB (WB, direct mapped, alias=0) ITLB entries : 240 DTLB entries : 240 - shared with ITLB bogomips : 1594.36 software id : 4473333560712706520 processor : 3 cpu family : PA-RISC 2.0 cpu : PA8900 (Shortfin) cpu MHz : 799.997100 physical id : 1 siblings : 2 core id : 1 capabilities : os64 iopdir_fdc needs_equivalent_aliasing (0x35) model : 9000/800/rp3440 - Storm Peak Slow Mako+ hversion : 0x00008950 sversion : 0x00000491 I-cache : 65536 KB D-cache : 65536 KB (WB, direct mapped, alias=0) ITLB entries : 240 DTLB entries : 240 - shared with ITLB bogomips : 1594.36 software id : 4473333560712706520 00:01.0 USB controller: NEC Corporation OHCI USB Controller (rev 41) 00:01.1 USB controller: NEC Corporation OHCI USB Controller (rev 41) 00:01.2 USB controller: NEC Corporation uPD72010x USB 2.0 Controller (rev 02) 00:02.0 IDE interface: Silicon Image, Inc. SiI 0649 Ultra ATA/100 PCI to ATA Host Controller (rev 02) 20:01.0 SCSI storage controller: Broadcom / LSI 53c1010 66MHz Ultra3 SCSI Adapter (rev 01) 20:01.1 SCSI storage controller: Broadcom / LSI 53c1010 66MHz Ultra3 SCSI Adapter (rev 01) 20:02.0 Ethernet controller: Broadcom Inc. and subsidiaries NetXtreme BCM5701 Gigabit Ethernet (rev 15) 60:01.0 Ethernet controller: Broadcom Inc. and subsidiaries NetXtreme BCM5701 Gigabit Ethernet (rev 15) e0:01.0 Communication controller: Hewlett-Packard Company Device 0000 (rev 01) e0:01.1 Serial controller: Hewlett-Packard Company Diva Serial [GSP] Multiport UART (rev 03) e0:02.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Device 0000